User manual LG BD-300

[. . . ] Network Blu-ray Disc Player Owner's Manual Model: BD300 Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely. Internet Address:http://www. lg. ru »ÌÙÓÏ^ËÓÌÌ ÒÎÛÊ· LG Electronics (095)771-76-76 Internet address ; http://ua. lge. com Customer Information Center LG ; (380-44) 490-7777, 8-800-303-0000 As an ENERGY STAR® Partner, LG has determined that this product or product models meet the ENERGY STAR® guidelines for energy efficiency. registered mark. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. CAUTION concerning the Power Cord CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] [YCbCr] ­ Select when connecting to a HDMI display device. [RGB] ­ Select when connecting to an RGB display device. General Operation 1. Use v / V to select the desired option then press B to move to the second level. The screen shows the current setting for the selected item, as well as alternate setting(s). Use v / V to select the second desired option then press B to move to the third level. Use v / V to select the desired setting then press ENTER to confirm your selection. Press RETURN or HOME to exit the Setup menu. [DISPLAY] Menu 19 Installation and Setup Note: You cannot select [4:3 Letter Box] and [4:3 Pan Scan] option when the resolution is set to higher than 720p. [LANGUAGE] Menu [PCM Stereo] ­ Select if you connect this unit's HDMI OUT or DIGITAL AUDIO OUT jack to a device with two-channel digital stereo decoder. [PCM Multi-Ch] (HDMI only) ­ Select if you connect this unit's HDMI OUT jack to a device with multi-channel digital decoder. [DTS Re-Encode] ­ Select if you connect this unit's HDMI OUT or DIGITAL AUDIO OUT jack to a device with DTS decoder. Display Menu Select a language for the Setup menu and onscreen display. Disc Menu / Disc Audio / Disc Subtitle Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu. [Original] ­ Refers to the original language in which the disc was recorded. [Other] ­ Press ENTER to select another language. Use number buttons then ENTER to enter the corresponding 4-digit number according to the language code list on page 36. [Off] (for Disc Subtitle) ­ Turn off Subtitle. Note: Depending on the disc, your language setting may not work for some discs. [Primary Pass-Thru] ­ Select if you connect this unit's DIGITAL AUDIO OUT and HDMI OUT jack to a device with LPCM, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and DTS-HD. Notes: · When [HDMI] option is set to [PCM Multi-CH], the audio may output as PCM Stereo if the PCM Multi-Ch information is not detected from HDMI device with EDID. · When [HDMI] and [SPDIF] options are set to [DTS Re-Encode], the DTS audio will output on BD-ROM disc, and the original audio will output on the other discs (like [Primary Pass-Thru]). (Maximum Sampling Frequency) [192KHz] ­ Select this if your A/V Receiver or Amplifier is capable of handling 192 KHz signals. [96KHz] ­ Select this if your A/V Receiver or Amplifier is NOT capable of handling 192 KHz signals. When this choice is made, this unit automatically converts any 192 KHz signals to 96 KHz so your system can decode them. [48KHz] ­ Select this if your A/V Receiver or Amplifier is NOT capable of handling 192 KHz and 96 KHz signal. When this choice is made, this unit automatically converts any 192 KHz and 96 KHz signals to 48 KHz so your system can decode them. [. . . ] If you set the [HDMI] option to [PCM Multi-CH] or [Primary Pass-Thru], the [SPDIF] option is set to [PCM Stereo] automatically. Also, if you set the [SPDIF] option to [DTS Re-encode] and the [HDMI] option is set to [PCM Stereo] automatically. *4 The LPCM audio recorded at 192kHz sampling frequency will be outputted as stereo sound. *5 On the PCM audio output, the sampling frequency of HDMI/SPDIF (DIGITAL AUDIO OUT) is limited to 96 kHz. [. . . ]