User manual LG BE320

[. . . ] DLP Projector BE320-SD Owner's Manual P/N: SAC30190915 Rev. A www. lg. com Table of Contents Table of Contents Usage Notice Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Appendices Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Replacing the lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 5.  o not turn on the projector immediately following a power D off procedure. English English 17 Installation Adjusting the Projected Image Adjusting the Height of Projector Image The projector is equipped with adjustable feet to raise and lower the image to fill the screen. To raise/lower the image: Use “Adjustable feet” to fine-tune the display angle. N ot e  You can raise the projector front up by rotating the adjustable feet. Adjustable feet 8 English Installation Adjusting the Projector’s Zoom and Focus To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 3. 28 to 39. 37 feet (1. 0 to 12. 0 meters) with mechanical travel. To turn the zoom lever to zoom in or out. Zoom Lever Focus Ring Adjusting Projection Image Size Projection Image Size from 22. 9” to 255. 0” (0. 6 to 6. 48 meters). Top View Screen Screen (W) Height Projection Distance (D) Dia go na l Screen Side View Screen (H) Width Offset (Hd) Projection Distance (D) English English 9 Installation Diagonal length (inch) size of 4:3 Screen 30 40 60 70 80 90 100 120 150 180 250 300 Screen Size W x H (meter) Width 0. 610 0. 813 1. 219 1. 422 1. 626 1. 829 2. 032 2. 438 3. 048 3. 658 5. 080 6. 096 Height 0. 457 0. 610 0. 914 1. 067 1. 219 1. 372 1. 524 1. 829 2. 286 2. 743 3. 810 4. 572 24 32 48 56 64 72 80 96 120 144 200 240 (inch) Width Height 18 24 36 42 48 54 60 72 90 108 150 180 Projection Distance (D) (meter) wide 1. 183 1. 577 2. 365 2. 759 3. 154 3. 548 3. 942 4. 731 5. 913 7. 096 9. 855 11. 826 tele 1. 301 1. 735 2. 602 3. 035 3. 469 3. 903 4. 336 5. 204 6. 504 7. 805 10. 841 13. 009 (feet) wide 3. 880 5. 173 7. 760 9. 053 10. 347 11. 640 12. 933 15. 520 19. 400 23. 280 32. 333 38. 800 tele 4. 268 5. 691 8. 536 9. 959 11. 381 12. 804 14. 227 17. 072 21. 340 25. 608 35. 567 42. 680 Offset (Hd) (m) 0. 069 0. 091 0. 137 0. 160 0. 183 0. 206 0. 229 0. 274 0. 343 0. 411 0. 572 0. 686 (feet) 0. 225 0. 300 0. 450 0. 525 0. 600 0. 675 0. 750 0. 900 1. 125 1. 350 1. 875 2. 250  Both side view and top view refer to the above table.  This table is for user’s reference only. 20 English User Controls On Screen Display The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1.  o open the OSD, press “MENU” on the Remote Control or Control T Panel. 2. When OSD is displayed, use keys to select any item in the  main menu. While making a selection on a particular page, press or key to enter sub menu. keys to select the desired item in the sub menu and 3.  se U adjust the settings using key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. Press “OK” to confirm, and the screen will return to the sub menu. 6.  o exit, press “MENU” repeat again. The OSD will be closed and T the projector will automatically save the new settings. Main Menu Sub Menu Setting English English 21 User Controls IMAGE Picture Mode There are many factory presets optimized for various types of im ages.  Presentation: This mode is suitable for showing in front of public in connection to the PC. N ot e  When you change the items, the picture mode will be set “User1”.  High-Bright: This mode is recommended when you want maximum brightness. C   lassroom: This mode is recommended for projecting in a class-  Movie: This mode is suitable for watching video.  sRGB: Standardized accurate color.   lackboard: This mode should be selected to achieve optimum B color settings when projecting onto a blackboard (green).  User1/User2: Memorize user’s settings. Brightness Adjust the brightness of the image. (range: 0~100)  Press the  Press the to darken image. to lighten the image. Contrast  he contrast controls the degree of difference between the lightest T and darkest parts of the picture. (range: 0~100) 22 English User Controls  Press the  Press the N ot e to decrease the contrast. to increase the contrast. Sharpness Adjust the sharpness of the image. (range: 0~31)  “Sharpness”, “Saturation” and “Hue” functions are only supported under Video mode.  Press the  Press the Saturation to decrease the sharpness. to increase the sharpness. Adjust a video image from black and white to fully saturated color. (range: 0~100) to decrease the amount of color in the image. [. . . ] Clear the lamp hours by selecting “OPTIONS” -> “Lamp Settings” -> “Clear Lamp Hours” from the menu.  Fan failed - the system fan is not working. English English 41 Appendices Replacing the lamp The projector will detect the lamp life itself. It will show you a warning message When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 45 minutes before changing the lamp. Warning: Lamp compartment may be hot! Allow it to cool down before changing the lamp! Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.  English Appendices N ot e  The screws on the lamp cover and the lamp cannot be removed.  Do not touch the glass area of the lamp. Hand oil can cause the lamp to shatter. Use a dry cloth to clean the lamp module if it was accidentally touched. 2 1 4 3 5 6 Lamp Replacing Procedure: 1. witch off the power to the projector by pressing the “POWER ”. S 2. Allow the projector to cool down at least 45 minutes. 4. Unscrew the one screw on the front cover.  5. Push and slide the top cover  and then open the top cover.  6. emove the 2 screws from the lamp module  and pull up the lamp bar.  R 7. Pull out the lamp module by force.  8. nstall the new lamp module by reversing the previous steps. I 9. fter replacing the lamp, turn on the power, and select the menu -> A [OPTIONS|Lamp Settings] ->[Clear Lamp Hours] to reset the lamp usage hours. refer to page 33. English English 3 Appendices Compatibility Mode Computer Compatibility (Analog, PC) Modes VGA Resolution 640 x 350 640 x 480 640 x 480 640 x 480 720 x 400 SVGA 800 x 600 800 x 600 800 x 600 V-Sync (Hz) 70 60 72 75 70 56 60 72 75 60 70 75 60 60 60 75 60 75 60 60 60 60 H-Sync (kHz) 31. 50 31. 50 37. 90 37. 50 31. 50 35. 20 37. 90 48. 10 46. 90 48. 40 56. 50 60. 00 47. 40 45. 00 49. 702 67. 50 63. 98 79. 98 60. 00 63. 98 65. 30 75. 00 N ot e  Please note that using resolutions other than native 800 x 600 (SVGA) may result in some loss of image clarity. [. . . ]