User manual LG BHD-651-D

[. . . ] Indoor Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outdoor Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS OF ELECTRICAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (1) Open the screw caps and remove the two screws securing the front cabinet. (3) Open the vertical airflow louver horizontally by hand. (4) Slightly open the lower part of the front cabinet then pull the upper part of the front cabinet toward you to remove it from the rear plate. 10mm 40mm Earth line NOTE : · Use standard wire only. · Wire type: More than H05-RNF Fig. 8-4-8 ­ 28 ­ <How to connect the connecting cable> Wiring of the connecting cable can be carried out without removing of the front panel. Disengage the support arm located in the upper center while pushing its handle leftwards, and then remove the front panel toward you. (2) Remove the terminal cover and cord clamp. (3) Insert the connecting cable (according to local codes) into pipe hole on the wall. (4) Take out the connecting cable through the cable slot on the rear panel so that it is exploded by about 15 cm long in the front side. (5) Insert the connecting cable fully into the terminal block and secure it by screw tightly. (6) Tightening torque:1. 2 N·m (0. 12 kgf·m) (7) Secure the connecting cable with the cord clamp. Pull the indoor unit toward you by the lower part to confirm that it is firmly hooked up on the installation plate. (1) 8-4-6. Drainage (1) Run the drain hose sloping downwards. NOTE : · Hole should be made at a slight downward slant to the outdoor side. Do not rise the drain hose. Do not form the drain hose into the wared shape. 50 mm or more Do not put the drain hose end into water. Do not put the drain hose end in the drainage ditch. Hook here 1 Installation plate (2) Fig. 8-4-17 (2) Put water in the drain pan and make sure that the water is drained outdoors. (3) When connecting extension drain hose, insulate the connecting part of extension drain hose with 5 shield pipe. 5 Shield pipe Hook Push Fig. 8-4-15 · For detaching the indoor unit from the installation plate pull the indoor unit toward you while pushing its bottom up by the specified parts. Drain hose Inside the room Extension drain hose Fig. 8-4-18 CAUTION Push Push Arrange the drain pipe for proper drainage from the unit. Improper drainage can result in damage to property. This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide. Wall Drain guide Fig. [. . . ] Remarks Replace the thermal fuse, terminal block, power cord, microcomputer ass'y and the power supply PC board ass'y. Thermal fuse replacement ­ 55 ­ 10-3. Outdoor Unit (RAS-13SAH-E, RAS-13SAHX) No. Part name Common procedure Procedure 1) Stop the operation of air-conditioner, and disconnect the power cord from the AC supply. (2- ST1T ø4 x 10 ) 3) Remove the cord clamp (2- ST2T ø4 x 12 ) and remove the connecting cable. [. . . ]