User manual LG BS36DHL

[. . . ] 40 Configurations of Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Terminal : Analog RGB (Mini D-sub 15 pin) . . . . . . 41 Terminal : Mini DIN 3-pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Regulation & Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Audio in cable jack to jack 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S-Video cable 14 English Installation Powering On/Off the Projector Powering On the Projector 1. Ensure that the power cable and signal cable are securely connected. Turn on the lamp by pressing "POWER" on the control panel or the remote control. The startup screen will display in approximately 5 seconds. When disappear startup screen, the POWER LED will turn green. Turn on your source (computer, notebook, video player, etc. ) The projector will detect your source automatically. f you connect multiple sources at the same time, use the I "SOURCE" on the remote control or use "RGB", "S-video", "Video" on the remote control to switch inputs. 2 POWER OR N ot e Turn on the projector first and then the signal sources. Lens Cap 1 15 English English Installation Powering Off the Projector 1. Press the "POWER" to turn off the projector lamp, you will see a message as below on the on-screen display. 2. Press the "POWER" again to confirm. The cooling fan continues to operate for about 120 seconds for cooling cycle and the POWER LED will flash green. After adjusting the settings, press "MENU" go back to the main menu. The OSD will be closed and the projector will automatically save the new settings. Main Menu N ot e If no button operation is made for 30 seconds, the OSD will be closed automatically. Sub Menu Setting 20 English User Controls IMAGE Image Mode There are many factory presets optimized for various types of images. Use the or to select the item. Presentation: For computer or notebook. Blackboard: This mode should be selected to achieve optimum color settings when projecting onto a blackboard (green). Classroom: This mode is recommended for projecting in a classroom. User1/User2: Memorize user's settings. Brightness Adjust the brightness of the image. Press the Press the Contrast to darken image. to lighten the image. The contrast controls the degree of difference between the lightest and darkest parts of the picture. Press the Press the to decrease the contrast. to increase the contrast. English English 21 User Controls Sharpness Adjust the sharpness of the image. N ot e "Sharpness", "Saturation" and "Tint" functions are only supported under Video mode. Press the to decrease the sharpness. Saturation Adjust a video image from black and white to fully saturated color. Press the Press the Tint Press the Press the to decrease the amount of color in the image. to increase the amount of color in the image. Adjust the color balance of red and green. to increase the amount of green in the image. to increase the amount of red in the image. 22 English User Controls IMAGE | Advanced Gamma This allows you to choose a gamma table that has been fine-tuned to bring out the best image quality for the input. Film: For home theater. [. . . ] Make sure the projector has been cooled down for at least 45 minutes before changing the lamp. 1 2 3 4 Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the "POWER". Allow the projector to cool down at least 45 minutes. Use a screwdriver to remove the 2 screws from the cover. [. . . ]