User manual LG CA-20D63

[. . . ] Number of pages : 32 N O T E S "This part contain Eco-hazardous substances (Pb, Cd, Hg, Cr6+, PBB, PBDE, etc. ) within LG standard level, Details should be followed Eco-SCM management standard[LG(56)-A-2524]. Especially, Part should be followed and controlled the following specification. (1)Eco-hazardous substances test report should be submitted when Part certification test and First Mass Production. (2) Especially, Don't use or contain lead(Pb) and cadmium(Cd) in ink. 3. Special Instructions * LGENT : Printed in China * LGENP : Printed in China * LGEIL : Printed in India * LGEDI : Printed in Indonesia * LGEIN : Printed in Indonesia * LGEMA : Printed in Poland * LGETH : Printed in Thailand * LGEWA : Printed in U. K. [. . . ] UP/DOWN Installing Batteries I Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +, -with -). Don't mix old or used batteries with new ones. Close cover. I I 11 MFL34797073-en-simple 8/6/08 8:31 PM Page 12 PREPARATION CABLE MANAGEMENT I Image shown may differ from your TV. 12 PREPARATION 1 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. 2 Install the CABLE MANAGEMENT CLIP as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables. CABLE HOLDER CABLE MANAGEMENT CLIP CABLE MANAGEMENT CLIP How to remove the CABLE MANAGEMENT CLIP 42PG10/20/20C G 50PG10/20/20C, 50/60PG30, 50/60PG30C G First, press the cable management. Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward. Hold the CABLE MANAGEMENT CLIP with both hands and pull it upward. !NOTE G Do not hold the CABLE MANAGEMENT CLIP when moving the TV. - If the TV is dropped, you may be injured or the TV may be broken. MFL34797073-en-simple 8/6/08 8:31 PM Page 13 DESKTOP PEDESTAL INSTALLATION I Image shown may differ from your TV. For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. PREPARATION 4 inches 4 inches 4 inches 4 inches CAUTION G G Ensure adequate ventilation by following the clearance recommendations. Do not mount near or above any type of heat source. SWIVEL STAND (Only 50/60PG30, 50/60PG30C) After installing the TV, you can adjust the TV manually to the left or right direction by 20 degrees to suit your viewing position. 13 MFL34797073-en-simple 8/6/08 8:31 PM Page 14 PREPARATION VESA WALL MOUNTING Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are the same. 15 MFL34797073-en-simple 8/6/08 8:31 PM Page 16 PREPARATION I To prevent damage do not connect to the power outlet until all connections are made between the devices. ANTENNA OR CABLE CONNECTION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust antenna direction if needed. R Wall Antenna Socket Multi-family Dwellings/Apartments (Connect to wall antenna socket) ANTENNA/ CABLE IN Outdoor Antenna (VHF, UHF) RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) ( ) Copper Wire ( ) Be careful not to bend the copper wire when connecting the antenna. 2. Cable Cable TV Wall Jack RF Coaxial Wire (75 ohm) ANTENNA/ CABLE IN To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. I If the antenna needs to be split for two TV's, install a 2-Way Signal Splitter. I If the antenna is not installed properly, contact your dealer for assistance. I ( ) 16 R R PREPARATION MFL34797073-en-simple 8/6/08 8:32 PM Page 17 EXTERNAL EQUIPMENT SETUP I To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. HD RECEIVER SETUP This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the digital settop box to the C O M P O N E N T I N V I D E O 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and ( PR = red). Connect the audio output of the digital set-top box to the C O M P O N E N T I N A U D I O 1 jacks on the TV. 1 MOTE TROL IN RGB(PC) (RGB/DVI) EXTERNAL EQUIPMENT SETUP COMPONENT IN 2 HDMI/ 2 1 ) 1 VIDEO AUDIO 2 2. How to use I I 2 I Turn on the digital set-top box. [. . . ] I Ensure that the batteries are installed with correct polarity (+ to +, - to -). I Ensure that the correct remote operating mode is set: TV, VCR etc. I Install new batteries. I I Power is suddenly turned off Is the sleep timer set?Power interrupted. APPENDIX The video function does not work. [. . . ]