User manual LG CRD-8160B

[. . . ] Com A-2 TABLE OF CONTENTS TABLE OF CONTENTS A-3 SETTING UP THE TV A-3 A-7 Attaching the stand Tidying cables COMMON language list English Svenska Norsk Dansk Suomi LANGUAGE B-1 MAKING CONNECTIONS B-1 B-2 B-2 B-4 B-6 B-7 B-8 B-9 B-10 B-13 B-15 B-16 B-17 Antenna connection Satellite connection HDMI connection - ARC (Audio Return Channel) DVI to HDMI connection MHL connection RGB-PC connection Component connection Composite connection Euro scart connection Audio connection - Digital optical audio connection USB connection CI module connection Headphone connection B-22 SPECIFICATIONS COMMON SETTING UP THE TV A-3 SETTING UP THE TV Image shown may differ from your TV. Attaching the stand 47/55LM96** 1 Stand body 4 EA M4 x 20 4 4 EA M4 x 20 Front Stand base Top View 2 Stand rear cover 3 CAUTION yy Make sure that the screws are inserted correctly and fastened securely. If they are not fastened securely enough, the TV may tilt forward after being installed. Yy not use too much force and over tighten Do the screws; otherwise screw may be damaged and not tighten correctly. [. . . ] »  se this to install TV in a place where there is a voltage difference between TV set and GND of U antenna signal. If there is a voltage difference between TV set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an accident. »  ou can improve the safety when watching TV by efficiently removing power voltage from TV Y antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation. »  efore starting, be sure that the TV antenna is connected. Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box. €Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing - and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)” When applying the RF Isolator, a slight loss of signal sensitivity can occur. 16 ASSEMBLING AND PREPARING Separate purchase Separate purchase items can be changed or modified for quality improvement without any notification. Adjusting the angle of the TV to suit view Swivel 20 degrees to the left or right and adjust the angle of the TV to suit your view. 20˚ 20˚ 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. - If there are bolts inserted at the eye-bolts position, remove the bolts first. 2 Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface. CAUTION yy Make sure that children do not climb on or hang on the TV. CAUTION yy When adjusting the angle of the product, watch out for your fingers. Personal injury may occur if hands or fingers are pinched. If the product is tilted too much, it may fall, causing damage or injury. [. . . ] 2 /DVI IN Connect a USB storage device such as a USB flash memory, external hard drive or a USB memory card reader to the TV and access the Smart Share menu to use various multimedia files. Is not Max LNB Satellite / CABLE NOTE AUDIO Check if the CI module is inserted into the yy PCMCIA card slot in the right direction. If the module is not inserted properly, this can cause damage to the TV and the PCMCIA card slot. IN ANTENNA OPTICAL H/P DIGITAL Satellite / CABLE AUDIO 13/18V 700mA Max LNB IN OUT English Transmits the headphone signal from the TV to an external device. [. . . ]