User manual LG CS990DC

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. A2 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. When attached, tighten the thumbscrews to secure the connection. Connect the power cable 3 with the AC-DC adapter (AC-DC power supply) 2 , and then plug the cable in the outlet. 2. Connect the signal cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product. [ Arranging the cables] Wall-outlet type PC-outlet type DVI-D(This feature is not available in all countries. ) [ Connecting the cables] Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 4. Touch the power button in front to turn on the monitor. The best display mode is: 1680 x 1050 AUTO/SET Button Power Button Use this button to turn the display on or off. Power Indicator This Indicator lights up as blue when the display is operating normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to blue LED blinking state. A7 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A8 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. EZ ZOOMING 4:3 IN WIDE PHOTO EFFECT NORMAL GAUSSIAN BLUR SEPIA MONOCHROME BRIGHTNESS CONTRAST GAMMA sRGB PRESET COLOR RED GREEN BLUE HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS LANGUAGE OSD POSITION SETUP HORIZONTAL VERTICAL WHITE BALANCE RTC POWER INDICATOR FACTORY RESET MOVIE INTERNET USER NORMAL DEMO 6500K 9300K To adjust the resolution To adjust the image size To adjust screen color mode PICTURE To adjust the brightness, contrast and gamma of the screen To customize the color of the screen To adjust the position of the screen To improve the clarity and stability of the screen TRACKING To customize the screen status for a user's operating environment FLATRON F-ENGINE To select or customize desired image settings : Adjustable A : Analog Input D : Digital Input NOTE The order of icons may differ depending on the model (A9~A16 ). A9 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. [. . . ] · If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. · Try to turn on the PC. Do you see an "OUT OF · This message appears when the signal from the PC (video card) is out of horizontal or vertical RANGE" message on frequency range of the display. 'Specifications' section of this manual and configure your display again. Do you see a "CHECK SIGNAL CABLE" message on the screen? [. . . ]