User manual LG CZ-20D60

[. . . ] Do not use the product in damp place such as a bathroom or any place where it is likely to get wet. - This may cause a fire or could give an electric shock. If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the service center. - If you continue to use without taking proper measures, electrical shock or fire can occur. PRECAUTIONS IN MOVING THE PRODUCT WARNING Make sure to turn off the product. [. . . ] Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable. RS-232C Input (CONTROL&SERVICE) Port Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode. Audio Output Connect an external amplifier or add a subwoofer to your surround sound system. RGB/DVI Audio Input Connect the audio from a PC. 6 Audio/Video Input Connect audio/video output from an external device to these jacks. Component Input Connect a component video/audio device to these jacks. Antenna Input Connect RF antenna to this jack. USB Input Connect USB storage device to this jack. DC ADAPTER PORT Connect to the power cord socket. 7 2 3 8 9 4 10 5 STAND INSTALLATION ENGLISH Image shown may differ from your TV. When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation. ) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. Only 22LK3** Only 26/32LK3**, 32/42LK4** 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 2 Assemble the TV as shown. Assemble the parts of the Stand Body with the Stand Base of the TV Stand Body M4 x 20 Stand Base 3 Assemble the TV as shown. 4 Fix the 4 bolts securely using the holes in the back of the TV. M4 x 20 11 PREPARATION STAND INSTALLATION ENGLISH Only 19/22/26LV2*** Only 32LV2*** 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the parts of the Stand Body with the Stand Base of the TV 2 Assemble the parts of the Stand Body with the Stand Base of the TV Stand Body Stand Base M4 x 14 Stand Body Stand Base 3 Assemble the TV as shown. 3 Assemble the TV as shown. 4 Fix the 2 bolts securely using the holes in the back of the TV. 4 Fix the 4 bolts securely using the holes in the back of the TV. M4 x 16 M4 x 14 12 BACK COVER FOR WIRE ARRANGEMENT Image shown may differ from your TV. ENGLISH Only 22LK3** After Connecting the cables as necessary, install CABLE HOLDER as shown and bundle the cables. Only 26/32LK3**, 32/42LK4** 1 Connect the cables as necessary. When using the remote control, aim it at the remote control sensor on the TV. 1 REMOTE CONTROL KEY FUNCTION 18 ENGLISH POWER Switches the TV on from standby or off to standby. Adjusts the volume. 1 5 2 VOLUME UP / DOWN 3 Home Select a menu. Clears all on-screen displays and returns to TV viewing from any menu. Allows you to navigate the on-screen menus and adjust the system settings to your preference. OK Accepts your selection or displays the current mode. External input mode rotate in regular sequence. Returns to the previously viewed programme. Selects a programme. 2 3 4 Home 6 7 8 4 THUMBSTICK(Up / Down / Left / Right) 5 INPUT 6 Q. MENU Select the desired quick menu source. Installing Batteries Open the battery compartment cover on the back and install the batteries matching correct polarity (+with +, -with -). Do not mix old or used batteries with new ones. To remove the batteries, perform the installation a actions in reverse TURNING ON THE TV - When your TV is turned on, you will be able to use its features. S-VIDEO VIDEO 1ANT OUTFirstly, connect the power cord correctly. L R ENGLISH At this stage, the TV switches to standby mode. 2 In standby mode to turn TV on, press the / I, INPUT or P button on the TV or press the POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on. [. . . ] Station or cable channel experiencing problems, tune to another station. Station signal is weak, reposition the antenna to receive weaker stations. Check for sources of possible interference. Check antenna (Change the position of the antenna). [. . . ]