User manual LG DA3630

[. . . ] E-4 · BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6 · ADJUSTING THE AIR FLOW DIRECTION . . E-8 · TIMER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-9 · ONE-HOUR OFF TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] » Using a fluorescent lamp with a quick starter in the same room may interfere with transmission of the signal. » The unit can be affected by signals transmitted from the remote control of a television, VCR or other equipment used in the same room. » Do not leave the remote control in direct sunlight or near a heater. Also, protect the unit and remote control from moisture and shock which can discolour or damage them. SETTING THE CURRENT CLOCK TIME There are two clock modes: 12hour mode and 24-hour mode. Example: 5 o'clock in the afternoon Clock Display 12-hour mode PM 5:00 24-hour mode 17:00 MODE FAN 1 3 1 To set to the 12-hour mode, press the CLOCK button once in the first step. To set to the 24-hour mode, press the CLOCK button twice in the first step. SWING SET/C 2 3 + - Å| Å{ Å{ Å| 2 Press the TIME ADVANCE or REVERSE button to set the current time. » Keep the button pressed to advance or reverse the time display quickly. » The colon (:) blinks to indicate that the clock is functioning. NOTE: » The current time cannot be set when the timer is operating. E-5 ENGLISH P @ , AM BASIC OPERATION 1 Press the MODE button to select the operation mode. AUTO HEAT COOL DRY FAN ONLY 2 3 2 5 4 1 Press the ON/OFF button to start operation. » The red OPERATION lamp ( will light. ) on the unit 1H 3 MODE FAN SWING SET/C Press the THERMO. » In the AUTO and 2°C higher DRY mode, the indi1°C higher cator bars represent 1°C lower changes in tempera2°C lower ture. (The time can be set in 10-minute increments. ) Point the remote control at the signal receiver window on the unit and press the TIMER SET (SET/C) button. » The yellow TIMER lamp ( ) on the unit will light. » The unit will generate a beep when it receives the signal. » The unit will turn on prior to the set time to allow the room to reach the desired temperature by the programmed time. (Awaking function) 1H MODE FAN 4 Select the operation condition. 3 1 2 SWING SET/C + - COMBINED USE OF ON AND OFF TIMERS You can use the ON and OFF timers in combination. Example: To stop operation at 11:00 p. m. and resume operation (with the same mode and temperature settings) to bring the room temperature to the desired level by 7:00 a. m. AM 1 2 Set the TIMER OFF to 11:00 p. m. Set the TIMER ON to 7:00 a. m. PM The arrow ( or ) between the TIMER ON indicator and the TIMER OFF indicator shows which timer will activate first. NOTES: » You cannot programme the TIMER ON and TIMER OFF to operate the unit at different temperatures or other settings. » Either timer can be programmed to activate prior the other. E-10 ONE-HOUR OFF TIMER When the ONE-HOUR OFF TIMER is set, the unit will stop operating after one hour. 1H 2 NOTE: » The ONE-HOUR OFF TIMER operation has priority over TIMER ON and TIMER OFF operations. AUXILIARY MODE Use this mode when the remote control is not available. TO TURN ON , , , , , , , , , , Lift the front panel of the indoor unit and press the AUX. » The red OPERATION lamp ( ) on the unit will light and the unit will start operating in the AUTO mode. » The fan speed and temperature setting are set to AUTO. TEST RUN AUX. TO TURN OFF Press the AUX. [. . . ] 3 Push the centre part of the panel firmly to lock it in place. 2 1 CLEANING THE UNIT AND THE REMOTE CONTROL » Wipe them with a soft cloth. » Do not directly splash or pour water on them. Water can cause electrical shock or equipment damage. » Do not use hot water, thinner, abrasive powders or strong solvents. MAINTENANCE AFTER AIR CONDITIONER SEASON MAINTENANCE BEFORE AIR CONDITIONER SEASON 1 2 3 Operate the unit in the FAN ONLY mode for about half a day to allow the mechanism to thoroughly dry. [. . . ]