User manual LG DK6822P

[. . . ] Do NOT insert anything between the air flow blades, as the inner fan may be damaged and you may be hurt. Particularly, keep children away from the indoor unit. Do NOT place any obstacles in front of the outdoor unit. If the remote control will not be used for a long time, remove the batteries. [. . . ] Result: x The indoor unit beeps each time you press x The air conditioner starts up in Cool mode. MODE . N o t e You can change modes at any time. MODE TURBO OFF 3 To adjust the temperature, press the or buttons one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. Result: x Each time you press or : - The temperature is adjusted by 1°C - The indoor unit beeps x The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature; the fan will, however, operate. button one or more times MODE TURBO OFF 4 Select the fan speed by pressing the until the required setting is displayed: Low Medium High Automatic Result: Each time you press , the indoor unit beeps. 5 To control the direction of the air flow, refer to page 15. E-10 Heating Your Room You must select the Heat mode if you wish to adjust the: x Heating temperature x Fan speed when heating 1 If necessary, press the Result: (On/Off) button. ENGLISH x The OPERATION indicator on the indoor unit comes on. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up normally after a three-minute. MODE TURBO OFF IM IMPORTANT 2 If the indication is not displayed at the top of the remote control, press the MODE button on the remote control one or more times until it appears. Result: x The indoor unit beeps each time you press x The air conditioner starts up in Heat mode. MODE . N o t e You can change modes at any time. MODE TURBO OFF 3 To adjust the temperature, press the or buttons one or more times until the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. 1 If necessary, press the Result: (On/Off) button. ENGLISH x The OPERATION indicator on the indoor unit comes on. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up normally after a three-minute. MODE TURBO OFF IM IMPORTANT 2 If the indication is not displayed at the top of the remote control, press the MODE button on the remote control one or more times until it appears. Hold down the w button. MODE TURBO OFF 3 4 To set the switch-on time, press the To. . . Increase the time in ten-minute intervals Increase the time in one-hour intervals Decrease the time in ten-minute intervals Decrease the time in one-hour intervals Result: 5 AM or PM is displayed to indicate whether the setting corresponds to a time before or after midday. . When you are satisfied with the switch-on time, press Result: Note x The indoor unit beeps. x The TIMER indicator on the indoor unit lights up yellow. If not necessary to operate the air conditioner until the set up time for starting, press (On/Off) button off. The air conditioner will start up automatically when the switch-on time is reached. button. 6 To set the switch-off time, press the Result: x The indication flashes. x The current preset time is displayed. 7 8 Set the switch-off time, following the instructions in Step 4. When you are satisfied with the switch-off time, press Result: . x The indoor unit beeps. x The TIMER indicator on the indoor unit lights up yellow. x The air conditioner will switch off automatically when the switch-off time is reached. [. . . ] x Check that you are close enough to the indoor unit (seven metres/ yards or less). x Check that you are pointing the remote control at the infrared sensor in the middle of the indoor unit. x Replace the remote control batteries if necessary. x Check that the correct operating mode has been selected ( , , ). [. . . ]