User manual LG DLG5955WM

[. . . ] 12 Child lock Dryer care Cleaning the lint filter . 14 Cleaning the exterior and the control panel. 16 Frequently asked questions Quick Guide Technical Service Installation instructions IMPORTANT SAFETY INSTRUCTIONS Caring for the environment Washer / Dryer Stack Electrical connection Installation Leveling the dryer . 27 Determining the position of the exhaust connection . [. . . ] At the end of a program The "Anti-crease/End" indicator will light at the end of a program and the buzzer will sound if it was selected. ^ Press the "Start/Stop T" button. Once the program starts, the current cycle of the program will be indicated in the "STATUS" display. If a fault occurred, a "FAULT" indicator will light. See "Frequently asked questions" for details. ^ Press the "Door" button. ^ Clean the lint filter after each use (see "Dryer care"). ^ Close the door. ^ Press the "On/Off" button to turn off the dryer. 11 Using the dryer Canceling or changing a program ^ Press and release the "Start/Stop T" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or - button. ^ Select a dryness level (available in the "Normal" and "Wrinkle-free" programs). ^ Press and release the "Start/Stop T" button to start the new program. Adding or removing laundry during a program ^ Turn off the dryer using the "On/Off" button. ^ Open the door. , CAUTION - Do not touch the rear of the drum while adding or removing items!The air supply in the room is insufficient. Clean the lint filters. Remove lint and check the exhaust system for blockages. Open a window or door to increase airflow. 17 Frequently asked questions What if the "Filter/Vent" indicator lights after cleaning the exhaust system? Possible fault Fix The dryer is not operating efficiently because the duct hose is too long. Check the exhaust length and diameter (see "How to calculate the effective duct length"). A long exhaust hose will increase program times and energy consumption. If the exhaust hose cannot be shortened, the indicator can be turned off by a service technician. What if the program runs too long or stops? Possible fault Fix The airflow is insufficient in the area of the dryer. The lint filters are clogged. Open a window or door to increase airflow. Clean the lint filters (see "Dryer care"). The laundry was not spun sufficiently in Select a higher spin speed in the wash the washer. Metal zippers interfere with the dryer's moisture sensors. Select a timed program to avoid overdrying. An airflow gap of 3/8" (10 mm) must be This gap must not be blocked by a provided between the machine and the toekick or thick piled carpets for sufficient airflow. What if the laundry is not dry enough? Possible fault The load contained too many dissimilar items (size and fabric. ) What if water has collected around the drum opening? Possible fault This is condensed moisture from the laundry. 18 Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer. Quick Guide 1. Turn on the dryer and load the laundry 2. Select a program ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. [. . . ] A 3 pole-4 wire grounding power outlet (NEMA type 14-30 R) is necessary. EASY INSTALLATION KIT If you do not have a dedicated 15 Amp line for this appliance, but you have the standard, 120/208-240 V - 30 Amp, 60 Hz AC outlet, you can use the "Easy Installation Kit", which allows you to use that line to connect the dryer to power. 057B for on-site outlet NEMA 10-30 R 060B for on-site outlet NEMA 14-30 R For more information on the "Easy Installation Kit" or if you have questions concerning the electrical connection, please contact: U V 1-800-999-1360 techserv@mieleusa. com 1-800-565-6435 service@miele. ca 25 Installation a Exhaust connection: The exhaust hose can be installed either at the rear, left or right of the dryer. b Power cord with plug c Control panel d Door e Four height adjustable feet 26 Installation Leveling the dryer Determining the position of the exhaust connection The exhaust connection can be left at the rear of the dryer (factory standard) or moved to the left or right side of the dryer. [. . . ]