User manual LG DOTR12CS

[. . . ] It may cause product breakdown. If the product was submerged under water, ask the service center for instruction. It may cause fire or an electric shock unless you do that. v Ser ice Cen ter CAUTION Make sure children or senor citizens use the product under proper observation in order to prevent safety accident. Do not pick the product with a sharp tool. It may cause product breakdown with the damage to its parts. I In-use Do not clean the product with strong cleanser such as solvent. [. . . ] Wired Remote Controller DOTR12CS Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run 2. Connecting Cable and Connector Cooling Heating Auto Dry Fan MODE FAN SPEED Accessory Connecting Cable (1EA) Fixing Screw (2EA) User / Installation Manual Installation Paper Owner's & Installation Manual 5 Part Description Simple Wired Remote Controller 1. Operation Display Panel DOTR12CS Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run 1 2. Temperature Control Button Cooling Heating Auto Dry Fan 2 3 4 5. Mode Selection Check Button MODE FAN SPEED 5 Each function will be shown on the display panel for three second or so when the power is applied at first. 6 Simple Wired Remote Controller Wired remote controller switch information Wired remote controller switch information Group Control 1 2 S/W GR Ceiling Height/Default E. S. P 1 2 3 S/W 2 Room Temp. Sensing 123 Product selection switch 1. HEAT PUMP product Indoor temperature sensor selection switch 1. Use the temperature sensor on the remote controller 2. Use the temperature sensor on the product. Use the sensor with the lower temperature between the remote Ceiling height selection switch 1. High ceiling S/W 1 Select Product 1 2 S/W Group control switch 1. The value of E. S. P can be adjusted from 1 to 255. If you press the On/Off button while setting the ESP function, it will be canceled. (The picture on the left side is the example of setting the Hi wind to ESP 10. ) MODE FAN SPEED 4 EX) Press the mode button and the temperature increasing button (L) same time for three seconds. Then the ESP setting will be activated after the temperature display flashes three times. Lo Med 200 Setting the Low wind to 210 100 Setting the Medium wind to 175 * The E. S. P value is set at the proper value at the factory. So it is highly recommended that you should not change the E. S. P value at your discretion. Owner's & Installation Manual 11 How to use the Mode Selection Button How to use the Mode Selection Button Cooling Operation 1 2 DOTR12CS Cooling operation will begin if you press the On/Off button. Plasma function is always operating for working if product has plasma function. Press the temperature button and set the desired temperature lower than the current room temperature. (18~30°C) A click of the button will increase the desired temperature by 1°C. A click of the button will decrease the desired temperature by 1°C. Defrost Preheat Out door * If the desired temperature is set higher than the current room temperature, the cooling function will not begin and just the blowing operation will continue. MODE FAN SPEED 3 If you press the mode button during the operation, the operation mode will be changed in the order of cooling, heating, dry(dehumidification), fan and auto-operation. If the product is a Cooling-Only model, the operation mode will be changed in the order of cooling, dry(dehumidification), fan and auto-operation. 4 If you press the On/Off button, the cooling operation will stop. 12 Simple Wired Remote Controller How to use the Mode Selection Button Heating Operation 1 2 DOTR12CS If you want to set the heating operation, press the On/Off button. Plasma function is always operating for working if product has plasma function. Set the desired room temperature higher than the current room temperature. [. . . ] It will take time for the product to blow warm air. The room will be heated with warm air after three minutes when the compressor begins operation. I The cooling-only model will not do heating function. Owner's & Installation Manual 13 How to use the Mode Selection Button Auto-Operation 1 DOTR12CS Set the operation mode to auto-operation after pressing the On/Off button. · If you press the fan button, the speed of the fan will change in the order of Low>Medium>Hi>Power. · The initial fan speed is "Hi" · If the product is not compatible with the Fan speed control, it will not function as per your selection. Fan Speed Selection in Cooling Operation DOTR12CS Defrost Preheat Out door Room Temp Total on Central Run Lo Med Hi Po MODE FAN SPEED Fan Speed Selection in Heating, Dry, Fan, Auto-Operation Lo Med Hi 16 Simple Wired Remote Controller How to use the Mode Selection Button Indoor Temperature Display DOTR12CS 1 Preheat Out door Room Temp Defrost When the fan speedbutton is pressed on the remote controller for about 3 seconds, the indoor temperature will be displayed for about 5 seconds, then goes back to the previous screen. [. . . ]