User manual LG DV8600H

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. x Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. x Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. [. . . ] air Theunit conditioner is fitted with a protection mechanism to prevent the from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up automatically after about three minutes. 2 If the COOL indicator is not lit up on the unit: x Press the button on the remote control or x Press the button on the unit one or more times until the COOL indicator lights up x The unit beeps each time you press . Result: x The air conditioner starts up in Cool mode. 3 You can change modes at any time. To adjust the temperature, press the or button on the remote control one or more times until the required temperature is displayed. To adjust the temperature, press the or button on the unit one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. x Each time you press the temperature buttons: Result: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps x The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed to. . . x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. or x Press the on the unit until the indicator lights up Med Low Result: Each time you press a button, the unit beeps. 5 E-8 To control the direction of the air flow, refer to page 11. AHT18PGHBA_E_17335 04/2/23 10:38 Page 9 Heating Your Room You must select the Heater mode if you wish to heat your room to a specific temperature. You can also set the fan speed. Remote Control Control Panel 1 If necessary, press the (On/Off) button. x The operating mode indicator (COOL, FAN or HEATER) Result: on the unit comes on. (The air conditioner operates in the mode selected when the unit was last used. ) E-12 AHT18PGHBA_E_17335 04/2/23 10:38 Page 13 Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time. You can set the period of time from 1 hour to 24 hours. You can select the Off Timer only when the air conditioner is on. Remote Control Control Panel 1 Check that the air conditioner has been switched on; if necessary, press the (On/Off) button. 2 Set the operating time by pressing: x on the remote control or x on the unit one or more times. Possible times are between 1 hour and 24 hours inclusive. Result: x The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time. x The air conditioner switches off automatically when the operating time reaches zero. You can change the setting mode, fan speed, and air flow direction after setting the Off Timer. To Cancel the Off Timer To cancel the Off timer, press: x on the remote control or on the unit one or more times until " " is displayed. or x (On/Off) button on the remote control or unit (The air conditioner operates in the mode selected when the unit was last used. ) E-13 AHT18PGHBA_E_17335 04/2/23 10:38 Page 14 Setting the Sleep Timer The Sleep Timer can be used when you are cooling or heating your room to switch the air conditioner off automatically after a period of 8 hours. Remote Control Control Panel 1 2 If you wish to switch the unit off at a specific time, refer to page 13. Make sure that you have selected either COOL or HEATER mode. Press the or Press the Result: button on the remote control button on the unit until the SLEEP indicator lights up. x Each time you press a button, the unit beeps. x The "SLEEP" passes through the control panel for about 15 seconds and the " " will be displayed. [. . . ] Check that you are close enough to the unit (seven metres/yards or less). Check that you are pointing the remote control at the remote control sensor on the unit. Replace the remote control batteries if necessary. Check that the correct operating mode has been selected COOL or HEATER. [. . . ]