User manual LG DV8900

[. . . ] The appliance coupler is used as the disconnect device. Please make sure the device is installed near the wall outlet to which it is connected and that the outlet is easily accessible. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Owner's Manual/Cards 15-pin D-Sub Signal Cable Power Cord (Depending on the country) AC-DC adapter DVI-D Signal Cable (This feature is not available in all countries. ) NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. 4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° -5° 15° IMPORTANT It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. Do not touch or press the screen when adjusting the angle of the monitor. 5 Connecting the Display Connecting with the PC DV8900 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable 2 in order, then tighten the screw NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. Varies according to model. Wall-outlet type DVI-D (This feature is not available in all countries. ) When using a D-Sub signal input cable connector for Macintosh Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) Dsub VGA connector on the supplied cable to a 15 pin 2 row connector. 6 Connecting the Display turned on, the 'Self Image Setting Function' is executed automatically. Press the power button on the front panel to turn the power on. When monitor power is Power Button NOTE ` Self Image Setting Function'?The default setting is D-Sub. EXIT Button Exit the OSD(On Screen Display). Power Button & Power Indicator Use this button to turn the display on or off. The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is red. 12 On Screen Display (OSD) Control Adjustment Screen Adjustment DV8900 Making adjustments to the image size and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. To access a control, use the corresponding Buttons. Use the Use the // Buttons to adjust the image to the desired level. Button to select other upper menu items. Press the EXIT Button to exit from the OSD. 13 On Screen Display (OSD) Control Adjustment Screen Adjustment E2281VR/E2381VR Making adjustments to the image size and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: HIGH 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. To access a control, use the corresponding Buttons. [. . . ] Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. 28 Troubleshooting Display image is incorrect G The screen color is mono or abnormal. · Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. [. . . ]