User manual LG E1910PM

[. . . ] ENGLISH OWNER'S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODEL E1910PM E2210PM www. lg. com Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] The product may fall and get damaged or injure your foot. Positioning your display After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -4° to 16° Swivel Range : 356° 6 Connecting the Display Height Range : maximum 4. 33 inches (110. 0 mm) 110. 0 mm * Please be sure to remove the Locking pin to adjust the height. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). When adjusting the height of the screen, do not put your finger(s) in between the head of the monitor and the stand base. You can hurt your finger(s). WARNING You do not need to replace the Locking pin after it is removed, to adjust its height. ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 7 Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. 1. Lift the monitor to its highest height to utilize the Pivot function. Landscape & Portrait : You can rotate the panel 90 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand section 3. Be careful with the cables when rotating the screen. 8 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. and power cord 2 in order, then tighten the screw of the signal cable. A Connect DVI-D(Digital signal) Cable C Connect Audio Cable B Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When using a D-Sub signal input cable connector for Macintosh Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. Varies according to model. Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. Wall-outlet type DVI-D (This feature is not available in all countries. ) Headphone/Speaker 3. Press the power button on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power Button NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. 9 Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. 10 Control Panel Functions MODE Button Use this button to enter F-ENGINE, ORIGINAL RATIO(Only E2210PM), PHOTO EFFECT menus. [. . . ] In this case, please ask to the computer or the video card manufacturer. 24 Troubleshooting Display image is incorrect G The screen color is mono or abnormal. · Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. · Make sure the video card is properly inserted in the slot. · Set the color setting higher than 24 bits (true color) at Control Panel - Settings. G The screen blinks. · Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? G Have you installed the display driver? [. . . ]