User manual LG E2341T

[. . . ] ENGLISH OWNER'S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODEL E1941S E1941T E2041T E2041S E2241T E2241S E2341T E2441T www. lg. com Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] Make sure you push it until you hear it "click". Stand Body Hinge Body Stand Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Base 4. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 5. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 2. Place the monitor face Down on the cushion or soft cloth. 3. Remove the Stand Body and Stand Base from product in correct direction as shown in the picture. 4. Use a coin on the back of the Stand Base and turn the screw anticlockwise to loosen. 6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 7 Connecting the Display Connecting with the PC E1941T/E2041T/E2241T/E2341T/E2441T 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable 2 in order, then tighten the screw NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When using a D-Sub signal input cable connector for Macintosh Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. Varies according to model. Wall-outlet type Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. B A PC PC 3. Press the power button on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power Button NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. 8 Connecting the Display Connecting with the PC E1941S/E2041S/E2241S 1. [. . . ] 15 pin D-Sub Connector RGB Analog (0. 7 Vp-p/ 75 ohm) VESA 1600 x 900 @ 60 Hz VESA 1600 x 900 @ 60 Hz E2041S Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions & Weight Max Recommend DDC 2B On Mode Sleep Mode Off Mode < < : 20 W(Typ. ) 0. 3 W 0. 3 W Without Stand Width 47. 60 cm (18. 74 inch) Height 30. 30 cm (11. 92 inch) Depth 5. 70 cm ( 2. 24 inch) 2. 7 kg (5. 95 lb) With Stand Width 47. 60 cm (18. 74 inch) Height 36. 40 cm (14. 33 inch) Dept 16. 60 cm ( 6. 54 inch) Weight(excl. packing) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 1. 0 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type NOTE Information in this document is subject to change without notice. 25 Specifications Display 54. 6 cm (21. 5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54. 6 cm 0. 248 mm x 0. 248 mm (Pixel pitch) Horizontal Freq. Input Form 30 kHz to 83 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate Sync. Digital E2241T Sync Input Video Input Signal Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital VESA 1920 x 1080 @60 Hz VESA 1920 x 1080 @60 Hz Resolution Plug&Play Power Consumption Dimensions & Weight Max Recommend DDC 2B (Analog, Digital) On Mode Sleep Mode Off Mode : 24 W(Typ. ) 0. 3 W 0. 3 W Without Stand Width 50. 90 cm (19. 80 inch) Height 32. 20 cm (12. 67 inch) Depth 5. 80 cm ( 2. 28 inch) 2. 9 kg (6. 39 lb) < < With Stand Width 50. 90 cm (19. 80 inch) Heigh 38. 80 cm (15. 27 inch) Depth 16. 60 cm ( 6. 54 inch) Weight(excl. [. . . ]