User manual LG EC970W

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Use a coin on the back of the stand base and turn the screw clockwise to tighten. 3. Once assembled take the monitor up carefully and face the front side. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display After installation, adjust the angle as shown below. * With stand base Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 6 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. To access a control, use the corresponding Buttons. Use the Use the / Buttons to adjust the image to the desired level. Button to select other sub-menu items. Press the EXIT Button to exit from the OSD. 11 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. DSUB : D-SUB(Analog signal) input DVI-D : DVI-D(Digital signal) input HDMI : HDMI input Main menu Sub-menu BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL Supported signals DSUB DVI-D HDMI Description Standard image settings. PICTURE HDMI COLOR COLOR TEMP (PRESET) WARM MEDIUM COOL DSUB DVI-D HDMI Color temperature adjustments. (USER) SIX COLOR (RED/GREEN/ BLUE/CYAN/ MAGENTA/ YELLOW) HUE SATURATION RED GREEN BLUE GAMMA COLOR RESET DISPLAY HORIZONTAL VERTICAL CLOCK PHASE OVERSCAN DSUB To adjust the position of the screen To improve the clarity and stability of the screen DSUB HDMI HDMI VOLUME OTHERS LANGUAGE POWER INDICATOR WHITE BALANCE FACTORY RESET To adjust the volume To customize the screen status for a user's operating environment DSUB DVI-D HDMI DSUB DSUB DVI-D HDMI 12 On Screen Display(OSD) Selection and Adjustment Main menu Sub-menu ORIGINAL RATIO Supported input DSUB DVI-D HDMI Description SMART+ To adjust the image size DUAL WEB CINEMA MODE DSUB DVI-D MODE USER DSUB DVI-D HDMI It is a mode that the user can adjust each element. It can adjust the color mode of the Main Menu. It is a mode that the screen is adjusted to the best to view the videos. It is a mode that the screen is adjusted to the best for the text works. It is a mode that the screen is adjusted to the best to view pictures. It is a mode that the screen is adjusted to the standard sRGB. MOVIE TEXT PHOTO sRGB NOTE The order of icons may differ depending on the model (12~22). 13 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name Icons Submenus Exit Adjust (Decrease/Increase) Select another sub-menu Restart to select sub-menu Button Tip NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. 14 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS To adjust the brightness of the screen. (only for HDMI input) Recommend overscan function to turn on when connect AV equipment. VOLUME To adjust the volume of headphone/ Earphone. [. . . ] · Set the color setting higher than 24 bits (true color) at Control Panel - Settings. · Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. G The screen blinks. Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? G Have you installed the display driver?· Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www. lg. com. [. . . ]