User manual LG F-8073QD

[. . . ] Keep children away from the unit. 5 ALWAYS ensure that the power cable is in good condition. If the power cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact: x An authorized service center x The dealer from whom you purchased the air conditioner. 7 Do NOT place any blocking objects in front of the unit. 8 If the remote control will not be used for a long time, remove the batteries. [. . . ] Possible temperatures are between 18°C and 30°C inclusive. x Each time you press the temperature buttons: Result: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps x The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed to. . . x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. or x Press the on the unit until the indicator lights up x Press the button on the remote control. or x Press the on the unit until the indicator lights up Med Low Result: E-8 Each time you press a button, the unit beeps. 5 To control the direction of the air flow, refer to page 10. Airing Your Room ENGLISH If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. Remote Control 2 If necessary, press the (On/Off) button. x The operating mode indicator (COOL or FAN) on the Result: unit comes on. x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. Control Panel 3 If the FAN indicator is not lit up on the unit: x Press the button on the remote control or x Press the MODE button on the unit one or more times until the FAN indicator lights up Result: x The unit beeps each time you press MODE. Result: The fan runs at all times, while the compressor cycles on and off. If you select the Sleep Timer in the Energy Saving mode, the Energy Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode. Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used. Mode Cooling Indoor Temperature 21°C to 32°C approx. Outdoor Temperature 21°C to 43°C approx. 21°C to 54°C approx. (Middle East) Then. . . The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. Water may condense on and drip from the surface of the unit if it is used for long periods. Indoor Humidity 80% or less If the air conditioner is used at. . . Higher temperatures Lower temperatures Higher humidity levels E-14 Cleaning Your Air Conditioner (FA models) ENGLISH The air conditioner has two or three grille grooves depending on the model. E-15 Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time. IMPORTANT When cleaning the air conditioner, turn it off and pull out the power plug. [. . . ] Dust may be blocking the air filter; refer to page 15 or 16 for cleaning instructions. Check that there is no obstacle blocking the air flow into or out of the unit. Check that the air conditioner has been switched on; if necessary, press (On/Off) on the remote control or unit. The air conditioner does not operate with the remote control x x x x x No beep is heard when you press (On/Off) on the remote control The air conditioner does not cool x x x x The air flow direction does not change when you press the (or on the unit)button The timer is not correctly triggered x x Check that the timer has been programmed correctly; see page 11~13. Air the room. Odours are permeated in the room during air conditioning x Technical Specifications Design and specifications are subject to change without notice. [. . . ]