User manual LG FFH-976A

[. . . ] 10 1-4-1 Application for indoor remote controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1-4-2 Two remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1-4-3 Group control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1-4-4 Application controls for central remote controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fan mode select display The selected fan mode is displayed. (AUTO) (HIGH) (MED. ) (LOW) Filter display If "FILTER " is displayed, clean the air filter. CHECK display Displayed while the protective device works or a trouble occurs. 6 7 8 9 Set up temperature display The selected set up temp. Flap position display SWING display Displayed during up/down movement of the flap. Timer time display Time of the timer is displayed. (When a trouble occurs, the check code is displayed. ) Timer SETIN setup display When pushing the Timer SET button, the display of the timer is selected in order of [OFF] [OFF] repeat OFF timer [ON] No display. 10 4 5 83 Operation Section Push each button to select a desired operation. · The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing button only. 1 2 3 ADR 5 6 SET CL 4 ACL SENSOR 7 1 2 3 4 5 Operation select button Selects desired operation mode. Fan mode select button Selects a fan mode. Timer set button TIMER SET button is used when the timer is set up. Check button CHECK button is used for check operation. During normal operation, do not use this button. · This lamp flashes while a trouble occurs. lamp and lamp flash · If "pi, pi" sound is heard, the MODE lamp of the display lamp goes on, and the alternately, the operation is not performed with the desired mode. 86 Signal Receiving Part (TCB-AX21E) · The signal receiving part is mounted to the ceiling panel. Signal Receiving Part 2 1 4 5 6 7 3 1 2 3 Temporary operation button Signal receiving part The signal sent from the remote controller is received. Display lamp One of displays flashed while a trouble occurs. When the display lamp flashes, refer to "Before asking of repair" in 95 page. 4 5 6 lamp This lamp goes on during operation. lamp This lamp goes on while the timer is reserved. lamp · In heating operation this lamp in the following cases; The operation has started. · This lamp flashes while a trouble occurs. lamp This lamp lights to indicate that it is time to clean the filter. lamp and lamp flash 7 · If "pi, pi" sound is heard, the MODE lamp of the display lamp goes on, and the alternately, the operation is not performed with the desired mode. 87 HOW TO OPERATE THE UNIT Cool/Heat AUTO, Heat, Dry, Cool, Fan Power supply Turn on the power of the wireless remote controller 12 hours before starting the operation. · After the power supply has been turned on, the operation of the remote controller is not accepted for approx. (The sensor receives the signal once, but the received contents are cleared. ) 1 2 3 4 1 2 3 Push Start/Stop button. Push (Operation Select button) opera, , , , and . tion to select one of Push (Fan Mode Select button) to select one of fan speed modes. [. . . ] (Refer to the section of "3-2-2". ) In this case, setting of the terminator resister on 1:1 models is unnecessary. (Remain SW01 as it is at shipment. ) 164 4. Installation Procedure · For installation of the adapter P. C. board and removal of the relay cable, be sure to wait a while (approx. [. . . ]