User manual LG FLATRON LCD 575MS(LB575EE)

[. . . ] If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation. Please use approved power cord provided by Philips all the time. If your power cord is missing, please contact with your local service center. (Please refer to Customer Care Consumer Information Center) Do not subject the LCD monitor to severe vibration or high impact conditions during operation. [. . . ] Such choices are disabled when using DVI-D (digit) input. Q&A Q1. What is the difference between SmartManage, SmartControl? A. SmartManage is a remote management/control software for IT managers to manage monitors across the network SmartControl is a control panel extension, which helps users to adjust monitor performances and settings by a software interface, instead of the hardware buttons at the front bezel of the monitors. I change the monitor on a PC to a different one and the SmartControl becomes un-usable, what do I do?Restart your PC and see if SmartControl can work. Otherwise, you will need to remove and reinstall SmartControl to ensure proper driver is installed. The SmartControl functions well at the beginning, but it is not workable, what can I do?If the following actions were executed, the monitor driver may need to be re-installed. %Ï %Ï %Ï %Ï %Ï Change video graphic adapter to another one Update video driver Activities on OS, such as service pack or patch Run Windows Update and updated monitor and/or video driver Windows was booted with the monitor power off or disconnected. To find out, please right click My Computer and click on Properties->Hardware-> Device Manager. If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install. Simply remove SmartControl and re-install it. After installing SmartControl, when clicking on SmartControl tab, nothing shows up after a while or a failure message shows, what happened?Other combinations of lit and dark sub pixels appear as single pixels of other colors. Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is, a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are the types of bright dot defects: One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple Three adjacent lit sub pixels - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) (one white pixel) A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots. Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern. These are the types of black dot defects: One dark sub pixel Two or three adjacent dark sub pixels Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables. BRIGHT DOT DEFECTS MODEL 1 lit subpixel 2 adjacent lit subpixels 3 adjacent lit subpixels (one white pixel) Distance between two bright dot defects* Total bright dot defects of all types ACCEPTABLE LEVEL 150S7 2 1 0 <15 mm 2 BLACK DOT DEFECTS MODEL 1 dark subpixel 2 adjacent dark subpixels 3 adjacent dark subpixels Distance between two black dot defects* Total black dot defects of all types ACCEPTABLE LEVEL 150S7 5 2 0 <15 mm 5 TOTAL DOT DEFECTS MODEL Total bright or black dot defects of all types ACCEPTABLE LEVEL 150S7 5 Note: * 1 or 2 adjacent sub pixel defects = 1 dot defect Your Philips monitor is ISO13406-2 Compliant RETURN TO TOP OF THE PAGE Installing Your LCD Monitor · Front View Produt Description · Connecting to Your PC · The Base · Getting Started · Optimizing Performance Front View Product Description 1 2 3 4 5 6 AUTO To switch monitor's power On and Off To access OSD menu To adjust the OSD To adjust brightness of the display To adjust the OSD Automatically adjust the horizontal position, vertical position, phase and clock settings. RETURN TO TOP OF THE PAGE Rear View 1 2 3 Kensington anti-thief lock VGA input AC power input RETURN TO TOP OF THE PAGE Optimizing Performance %Ï For best performance, ensure that your display settings are set at 1024x768, 60Hz. Note: You can check the current display settings by pressing the 'OK' button once. The current display mode is shown in OSD main controls called RESOLUTION. %Ï You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance out of your monitor. Step-by-step instructions are provided to guide you through the installtion process. Click on the link to know more about this program. More about FP_setup4. 3. exe RETURN TO TOP OF THE PAGE Connecting to Your PC · Front View Product Description · Accessory Pack · Connecting to Your PC · Getting Started · Optimizing Performance · The base Accessory Pack Unpack all the parts. Power cord VGA cable EDFU pack RETURN TO TOP OF THE PAGE Connecting to Your PC 1) Connect the power cord to the back of the monitor firmly. [. . . ] Each downstream port can be individually enabled and configured at either full or low speed. The hub isolates low speed ports from full speed signaling. A hub consists of two portions: the Hub Controller and Hub Repeater. The repeater is a protocolcontrolled switch between the upstream port and downstream ports. [. . . ]