User manual LG FMN1860NT

[. . . ] (If applicable) The air conditioner must be plugged into its own specific power source, which must be installed in compliance with national wiring, earthing and safety regulations. DURING OPERATION If the power cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. This device must be installed according to the national electrical rules. The appliance must be installation that the plug should be easily accessible after installation. If the fuse on PC board is broken please change it with the type of T 3. 15A 250V. [. . . ] HI COOL MED COOL LOW COOL AW**P1HEA The air conditioner starts up in Cool mode. The fan starts up at the speed selected. You can change modes at any time. 2 To adjust the temperature, turn the temperature control dial to the desired position. Possible temperatures: Between 18 C and 29 C inclusive. Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. AW**P1HEAA 3 To control the direction of the air flow, refer to page 7 AW**P1HEA AW**P1HEAA E-5 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. 2 Set the operating mode selection dial to the HI FAN or LOW FAN position. Result: AW**P1HEA The air conditioner starts up in Fan mode. 3 To control the direction of the air flow, refer to page 7. AW**P1HEAA Switching the Air Conditioner Off You can switch the air conditioner off whenever you want. 1 To switch the unit off, simply set the operating mode selection dial to the OFF position. Result: The air conditioner stops operating. AW**P1HEA AW**P1HEAA E-6 Adjusting the Air Flow Direction Horizontally ENGLISH Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. 1 Set the air flow blade swing switch to the on position. Set the operating mode selection dial to "LOW FAN" and let it run of a few hours to dry the inside of the air conditioner thoroughly. Have not used the air conditioner for a long period of time E-8 Solving Common Problems ENGLISH Before contacting the after-sales service, perform the following simple checks. They may save you the time and expense of an unnecessary call. PROBLEM The air conditioner does not operate at all EXPLANATION / SOLUTION Check that the circuit breaker used for the air conditioner has not been triggered. Check that the power cable is plugged into a wall socket and the socket is switched on, if necessary. Check that the correct operating mode has been selected (cooling or airing). The air conditioner does not cool Check that the correct operating mode has been selected. Dust may be blocking the air filter; refer to page 9 cleaning instructions. Check that there is no obstacle blocking the air flow into or out of the unit. The air flow direction does not change when you set the air flow blade swing switch to the on position Odours are permeated in the room during air conditioning Check that the air conditioner has been switched on; if necessary, turn the operating mode selection dial; refer to page 7. Air the room. Technical Specifications Design and specifications are subject to change without notice. Model Power Supply 220-240V~, 50Hz ******HEA/EAA E-9 Installation Before installation, be sure to check the installation area for the air conditioner, and drain hose. [. . . ] Outdoor Side 45 45 Indoor Side 100mm or more E-10 Installation of the Drain Tube Fix the drain tube as shown in the figure. Rear Rubber cap Gasket Drain Tube Screws(2EA) Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area. In the case of an area where the drain pan can not be directly installed on the rear side of the unit after installing the air conditioner. Example: High storage 1 2 Open the front grille; refer to page 9. [. . . ]