User manual LG GCD-5228WH

[. . . ] It may cause fire or an electric shock unless you do that. v Ser ice Cen ter CAUTION Make sure children or senor citizens use the product under proper observation in order to prevent safety accident. Do not pick the product with a sharp tool. It may cause product breakdown with the damage to its parts. I In-use Do not clean the product with strong cleanser such as solvent. Use soft clothes in order to prevent fire or product deformation. [. . . ] • The product is being shipped with the cable connected only to the remote controller. Put each cable to the remote controller according to the color match Be careful not to alter the colors of the remote controller connection cables. Main frame CN-M C CN-ZONE CN-DISP IC01A C01K J14 Red Yellow Brown Side of remote Controller Side of Indoor Unit Fixing the remote controller Fixing the connecting cable 3 Remove the installation paper before installing the remote controller so that it can fit into the right place. * When installing the wired remote controller, do not install it so that it is buried to the wall. (This can cause error in the temperature sensor) * When installing multiple wired remote controllers horizontally in one location, leave a minimum distance apart (2cm). (This can cause error in the temperature sensor) * Do not install the cable with a distance of 50 m or longer. (This can cause communication error. ) * When installing the cable, check whether the connector between the remote controller and the product is installed properly. The connector will not be connected when installed in opposite sides. ❏ Supply the power after connecting wired remote controller. When you need to change wired remote controller, switch off the main power and change it Before switch off the main power if changed the wired remote controller , you can't use the option function of the indoor unit. 8 Deluxe Wired Remote Controller LO2K LO1D C07D LO1K CN-REMO J15 Necessary function before using Necessary functions before using Trial Operation The trial operation is to check the installation status of the product. The temperature will not be controlled during trial operation. Instead the product will operate in several modes such as cooling, strong wind, comp-on. ENGLISH 1 2 3 4 4 The trial operation is to check the installation status of the product. Instead the product will operate in several modes such as cooling, strong wind, comp-on. If you wan to do the trial operation, press the Special Function button and then select the trial operation mode. Then the product will begin the trial operation and the display will be like the following picture. The trial operation will continue for 18 minute or so and the product will go into standby mode. If you wan to cancel the trial operation during the process, press the On/Off button. * This function might not be available for Multi Product like Multi V system. Owner’s & Installation Manual 9 Necessary function before using Setting the Central-Control Address 1 2 Press the Special Function button. Press the address setting button. • If the product is not compatible with the heating function, it will not do the heating function. Owner’s & Installation Manual 19 Special Function Special Function This is a function to prevent tampering of settings by children or others. Child Lock You can use the child lock function. 1 2 Press the Special Function button of the remote controller. Press the child lock button. • A click of the child lock button will turn on/off the indicator. • If you press another button while adjusting child lock function, the temperature display will show CL for three seconds and then the operation will come back to the original mode. • If you want use the child lock function in standby mode, select child lock and press the On/Off button within three seconds. Then the standby mode will change into the child lock mode. • If you want to cancel the child lock function in the standby mode, just press the child lock button. 20 Deluxe Wired Remote Controller Special Function Vane control You can control the angle of the vane. ENGLISH 1 2 3 4 5 6 Select the Advanced Selection button on the control panel of the remote controller. Press the Vane Control button one more time to control the top and bottom vane. You will see the screen shown on the left. Press the Temperature Adjustment button to adjust the two vane angles from P0 to P5. Press the Vane Control button one more time to control the remaining two vane angles. Press the Vane Control button one more time to return to the original mode. • The vane angle that has been set does not change even when the air conditioner is turn off and on again (default is P0) Owner’s & Installation Manual 21 Special Function Swirl Swing You can use the swirl swing. 1 2 Press the Special Function button of the remote controller. Press the swirl swing button. • A click of the swirl swing will turn on/off the indicator. • If the product is not compatible with the swirl swing function, it will not do the function even though the indicator is turned on. Room Temperature Display 1 If you press indoor temperature button on the remote controller, the indoor temperature displays for 5 seconds. [. . . ] Select the day of week to set using the Day Selection button. After selecting the day of week, select the time to turn on the air conditioner using the Time/Minute button. Press the Time/Minute button one more time to set the minute using the Temperature Adjustment button and press the set button. After pressing the On/Off button decide the time to turn off the air conditioner using the Temperature Adjustment button. [. . . ]