User manual LG GCF-5238TI

[. . . ] Do not pick the product with a sharp tool. It may cause product breakdown with the damage to its parts. I In-use Do not clean the product with strong cleanser such as solvent. Use soft clothes in order to prevent fire or product deformation. [. . . ] It may cause product breakdown or an electric shock. 4 Simple Wired Remote Controller Part Description Part Description ENGLISH 1. Wired Remote Controller GCF-5238TI Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run 2. Connecting Cable and Connector Cooling Heating Auto Dry Fan ROOM TEMP FAN SPEED Accessory Connecting Cable (1EA) Fixing Screw (2EA) User / Installation Manual Installation Paper Owner’s & Installation Manual 5 Part Description Simple Wired Remote Controller 1. Operation Display Panel GCF-5238TI Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run 1 2. Temperature Control Button Cooling Heating Auto Dry Fan 2 3 4 5. Room Temperature Check Button ROOM TEMP FAN SPEED 5 Each function will be shown on the display panel for three second or so when the power is applide at first. 6 Simple Wired Remote Controller Installation Method Installation Method 1 Put the installation paper on the place and determine the position and height of the fixing screws of the wired remote controller. • Refer to the printed side of the installation paper. ENGLISH The position of the fixing screws CN-M C CN-ZONE CN-DISP IC01A C01K J14 Red Yellow Brown Main frame 3 Fixing the Remove the installation paper before installing remote controller the remote controller so that it can fit at the right place. 5㎝ * Do not embed the remote controller into the wall. (It may cause the breakdown of the temperature sensor. ) * If you want to install a number of remote controller at the same place in a vertical line, install them at regular intervals of 5cm. (It may cause the breakdown of the temperature sensor. ) ❐ Supply the power after connecting wired remote controller. If you press the On/Off button while setting the ESP function, it will be canceled. (The picture on the left side is the example of setting the Hi wind to ESP 10. ) ROOM TEMP FAN SPEED 4 EX) Press the room temperature button and the temperature increasing button (L) at the same time for three seconds. Then the ESP setting will be activated after the temperature display flashes three times. Lo Med 200 Setting the Low wind to 210 100 Setting the Medium wind to 175 * The E. S. P value is set at the proper value at the factory. So it is highly recommended that you should do not change the E. S. P value at your discretion. 10 Simple Wired Remote Controller How to use the Mode Selection Button How to use the Mode Selection Button Cooling Operation ENGLISH 1 2 GCF-5238TI If you want to start the cooling operation, press the On/Off button. The cooling mode can be set from Central Controller only. Press the temperature button and set the desired temperature lower than the current room temperature. (18~30°C) A click of the button will increase the desired temperature by 1°C. A click of the button will decrease the desired temperature by 1°C. Defrost Preheat Out door * If the desired temperature is set higher than the current room temperature, the cooling function will not begin and just the fan operation will continue. ROOM TEMP FAN SPEED 3 4 If you want to change mode during the operation, the operation mode will be changed by only Central Controller. If you press On/Off button again, the cooling operation will stop. What is the three-minute delay function?The function to protect the compressor delays the output of cool air when operating instantly after interrupting the cooling operation. Cooling operation restarts after 3 minutes when the compressor starts to operate. • You can choose the expected temperature from 18(C to 30(C. [. . . ] • It is recommended that the ideal difference of the temperature between indoors and outdoors should be less than 5°C. Owner’s & Installation Manual 11 How to use the Mode Selection Button Heating Operation 1 2 GCF-5238TI If you want to start the heating operation, press the On/Off button. The heating mode can be set from Central Controller only. Set the desired room temperature higher than the current room temperature. (16~30°C) Defrost Preheat Out door Room Temp Total on Central Run A click of the button will increase the desired temperature by 1°C. [. . . ]