User manual LG GC-F399BUQA

[. . . ] CONSTRUCTION VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS OF ELECTRICAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (Less than 10 seconds) The unit is in operation. three seconds, The green indicator flashes for 5 seconds. Motions The green indicator is on. The unit beeps three times. Hi POWER FILTER PAP TIMER OPERATION RESET If the unit is required to operate at this time, press [RESET] button once more or use the remote controller to turn it on. · While the filter check indicator is on, the RESET button has the function of filter reset betton. ­ 40 ­ 9-3-2. How to Cancel the Auto Restart Function To cancel auto restart function, proceed as follows : Repeat the setting procedure : the unit receives the signal and beeps three times. The unit will be required to be turned on with the remote controller after the main power supply is turned off. · When the system is on stand-by (not operating) Operation Press [RESET] button for more than three seconds. (Less than 10 seconds) The unit is on standby. three seconds, Motions The unit beeps three times and continues to operate. Hi POWER FILTER PAP TIMER OPERATION If the unit is not required to operate at this time, press [RESET] button once more or use the remote controller to turn it off. RESET · When the system is operating Operation Press [RESET] button for more than three seconds. (Less than 10 seconds) The unit is in operation. three seconds, Motions The green indicator is on. The unit beeps three times. Hi POWER FILTER PAP TIMER OPERATION If the unit is required to operate at this time, press [RESET] button once more or use the remote controller to turn it on. RESET 9-3-3. Power Failure During Timer Operation When the unit is turned off because of power failure during timer operation, the timer operation is cancelled. In that case, set the timer operation again. NOTE : The Everyday Timer is reset while a command signal can be received from the remote controller even if it stopped due to a power failure. ­ 41 ­ 9-4. PRESET OPERATION Set your preferred operation for future use. The setting will be memorized by the unit for future operation (except air flow direction). Press and hold PRESET for 3 seconds to memorize the setting. Press PRESET : Operate the preset operation. AUTO RESTART OPERATION To automatically restart the conditioner after the power failure (Power of the unit must be on. ) Setting 1. Press and hold the RESET button on the indoor unit for 3 seconds to set the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 secpmds) · Do not operate ON timer and OFF timer. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the operation. (3 beep sound but OPERATION lamp does not blink) 11. QUIET OPERATION To operate at super low fan speed for quiet operation (except in DRY mode) Press QUIET : Start and stop the operation. Note: Under certain conditions, QUIET operation may not provide adequate cooling or heating due to low sound features. [. . . ] 2) Open the air inlet grille, push the arm toward the outside, and remove the grille. Remarks 3) Press "PUSH" part under the front panel and remove hooks of the front panel from the installation plate. Installation plate Front panel Press ­ 74 ­ No. Part name Front panel Procedures Remarks 5) Remove the front panel fixing screws. (2 pcs. ) 6) Take off three hooks of panel from rear side. 2 Screws Three hooks <How to assemble the front panel> 1) Press three center positions and two lower center positions of the air outlet, and then hang the hanging hooks (3 pcs. ) at the top side of the front panel to the rear plate. 2) Tighten two screws. · Incomplete hanging or incomplete pressing may cause a dewdrops or generation of a fluttering sound. ­ 75 ­ No. Part name Electric parts box assembly Procedures 1) Follow the procedure up to 3) in above. [. . . ]