User manual LG GR-392CVF

[. . . ] PARTS REPLACEMENT 10-1 Indoor Unit 10-2 Outdoor Unit 11. EXPLODED VIEWS AND PARTS LIST 11-1 11-2 11-3 11-4 11-5 11-6 11-7 11-8 Indoor Unit (E-Parts Assy) (For Heat pump model) Indoor Unit (E-Parts Assy) (For Cooling model) Indoor Unit Outdoor Unit (GR-392CVF) Outdoor Unit (RAS-10UAH-ES4) Outdoor Unit (RAS-13UA-ES4) Outdoor Unit (RAS-10UA-ES4) Outdoor Unit (RAS-07UA-ES4) · This air conditioner is charged with HFC (R410A) that doesn't deplete the Ozone layer. · This air conditioner requires special installation for the refrigerant R410A. -2- FILE NO. SPECIFICATIONS MODEL ITEM Capacity 220V kW Phase Power source Power consumption Power factor Running current Indoor Outdoor V Hz kW % A A A lit/h dB dB kg mm mm 49 51 49 R410A 0. 95 Capillary tube 12. 7 Flare connection 6. 35 Flare connection m m RAS-13UKHP-ES4 Height Dimensions Net weight Evaporator type Indoor fan type High fan Air volume Medium fan Low fan Fan motor output Air filter OUTDOOR UNIT Height Dimensions Net weight Condenser type Outdoor fan type Airflow volume Fan motor output Compressor Safety device Louver type Usable outdoor temperature range °C 15 ~ 43 Model Output W m /h 3 RAS-13UKHP-ES4 GR-392CVF Cooling 240V 3. 82 220V 4. 32 1 220 - 240 50 1. 15 98 5. 20 1. 19 96 5. 00 30 2. 0 41/35/31 51 1. 18 98 0. 15 5. 35 5. 15 1. 22 96 3. 74 Heating 240V 4. 40 RAS-13UKP-ES4 RAS-13UA-ES4 Cooling 220V 3. 90 240V 3. 95 1. 19 98 5. 35 29 1. 23 97 5. 15 Starting current Moisture removal Noise Refrigerant Indoor (H/M/L) Outdoor (220-240V) Name of refrigerant Rated amount Gas side size Connection type Liquid side size Interconnection Connection type pipe Maximum length (One way) Maximum height difference INDOOR UNIT 49 50 Refrigerant control 15*1 6 RAS-13UKP-ES4 275 790 208 10 Finned tube Cross flow fan mm mm mm kg Width Depth m3/h m /h 3 630 520 430 650 550 490 20 Honeycomb woven filter with PP frame GR-392CVF 630 520 430 m3/h W RAS-13UA-ES4 550 780 270 mm mm mm kg 40 Width Depth 38 Finned tube Propeller fan 2120 2200 42 2120 2200 2030 30 2150 W PA150X2C-4FT 1100 Fuse, Overload relay Automatic louver -10 ~ 24 15 ~ 43 -3- FILE NO. [. . . ] If the connecting pipe is laid the indoor unit on the installation plate at the upper exceeding 43 mm above the wall surface, the indoor hooks. Swing the indoor unit to right and left to confirm that connecting pipe, make sure to use a spring bender so it is firmly hooked up on the installation plate. While pressing the indoor unit onto the wall, hook it at the lower part on the installation plate. Pull the Bend the connection pipe within a radius of 30 mm. indoor unit toward you to confirm that it is firmly To connect the pipe after installation of the unit (figure) hooked up on the installation plate. (To the forefront of flare) 1 270 mm 170 mm Hook here 1 Installation plate Liquid side Gas side 2 Hook Outward form of indoor unit 43 mm Press (unhook) R 30 mm (Use polisin (polyethylene) core or the like for bending pipe. ) Fig. 8-4-17 · For detaching the indoor unit from the installation plate, pull the indoor unit toward you while pushing its bottom up at the specified parts. 80 Use the handle of screwdriver, etc. Fig. 8-4-16 NOTE If the pipe is bent incorrectly, the indoor unit may unstably be set on the wall. After passing the connecting pipe through the pipe hole, connect the connecting pipe to the auxiliary pipes and wrap the facing tape around them. Push Push CAUTION · Bind the auxiliary pipes (two) and connecting cable with facing tape tightly. In case of leftward piping and rear-leftward piping, bind the auxiliary pipes (two) only with facing tape. Indoor unit Auxiliary pipes Connecting cable Installation plate Fig. 8-4-18 · Carefully arrange pipes so that any pipe does not stick out of the rear plate of the indoor unit. · Carefully connect the auxiliary pipes and connecting pipes to each other and cut off the insulating tape wound on the connecting pipe to avoid double-taping at the joint, moreover, seal the joint with the vinyl tape, etc. 8-4-20 CAUTION Arrange the drain pipe for proper drainage from the unit. Improper drainage can result in dew-dropping. This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide. Wall Drain guide Strong wind Space for pipes Fig. Cut the pipe with a pipe cutter. Obliquity Roughness Warp (Unit : N·m) Outer dia. of copper pipe 6. 35 9. 52 12. 70 Tightening torque 16 to 18 (1. 6 to 1. 8 kgf·m) 30 to 42 (3. 0 to 4. 2 kgf·m) 50 to 62 (5. 0 to 6. 2 kgf·m) 90° Fig. Insert a flare nut into the pipe, and flare the pipe. · Projection margin in flaring : A (Unit : mm) A · Tightening torque of flare pipe connections The operating pressure of R410A is higher than that of R22. It is therefore necessary to firmly tighten the flare pipe connecting sections (which connect the indoor and outdoor units) up to the specified tightening torque. Incorrect connections may cause not only a gas leakage, but also damage to the refrigerant cycle. Flare at indoor unit side Die Pipe Fig. of copper pipe 6. 35 9. 52 12. 70 R410A tool used 0 to 0. 5 0 to 0. 5 0 to 0. 5 Conventional tool used 1. 0 to 1. 5 1. 0 to 1. 5 1. 0 to 1. 5 Flare at outdoor unit side Fig. [. . . ] Fix the cross flow fan with the set screw at the position where the gap between the back body and the right surface of the cross flow fan is 6 mm. 2 2-Screws (R) 2 2-Screws (L) 6 mm 6 Set screw Middle of the fan motor terminal 6 Base bearing 1) Remove the front panel, electrical part, horizontal louver, heat exchanger and the cross flow fan following procedure 5. 2) Remove the 2 screws fixing the base bearing. 3) Remove the bearing from the base bearing. If the housing protrudes from the base bearing, put the housing in position and attach the bearing to the base bearing. 2 2-Screws - 72 - FILE NO. [. . . ]