User manual LG GR-F218-UTJA

[. . . ] BOTTOM FREEZER REFRIGERATOR User's Guide Please read this guide thoroughly before operating and keep it handy for reference at all times. TM >~ <~ ڷη ȷ, ο ~ >~ <~ > η ڷ< ~ ӷ , ̤~ ȷ ӷ ӷʤ ٤~ ȷ< <. P/No. MFL37933555 TABLE OF CONTENTS Safety Instructions Parts and Features Refrigerator Installation Unpacking Your Refrigerator Installation Base Cover Removing and Replacing Your Refrigerator Handles and Doors Leveling and Door Alignment Using Your Refrigerator 39 10 1118 11 11 11 Dairy Bin Utility Bin Freezer section Ice Bin Tilt-Out Door Basket Durabase Durabase Divider 1217 18 1926 19 19 19 20 20 21 Pull out Drawer Filter Care and Cleaning General Cleaning Tips Outside Inside Walls Door Liner and Gaskets Plastic Parts Condenser Coils Light Bulb Replacement 21 22 22 23 23 23 24 Power Interruptions When you go on vacation When you move About the Automatic Icemaker Connecting the Water Line Troubleshooting Guide 24 25 25 25 25 26 2728 27 27 27 27 27 27 2728 28 28 28 29 24 24 Ensuring Proper Air Circulation Multi-Flow Setting the Controls Adjusting Control Settings Food Storage Guide Storing Frozen Food Refrigerator section Water Dispenser Refrigerator Shelves Bottle Holder Crisper Humidity Control Removing Crisper Glide `N' Serve Modular Door Bin 30-32 3336 2 SAFETY MESSAGES BASIC SAFETY PRECAUTIONS This guide contains many important safety messages. Always read and obey all safety messages. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others, or cause damage to the product. [. . . ] To remove, pull the drawer out to full extension. Lift the front of the crisper up, then pull it straight out. To install, slightly tilt up the front and insert the drawer into the frame and push it back into place. Controls The control regulates the air temperature in the drawer. Set control level to COLD (print on surface) to provide normal refrigerator temperature. Use the COLDER (print on surface) setting for meats or other deli items. NOTE: Cold air directed to the Glide`N'Serve can decrease refrigerator temperature. Refrigerator control may need to be adjusted. To replace Glide`N'Serve 1 To remove the glass 1. Lift up the glass under the crisper cover. To remove, pull the drawer out to full extension. Lift the front of the drawer up, then pull it straight out. To install, slightly tilt up the front and insert the drawer into the frame and push it back into place. 23 USING YOUR REFRIGERATOR MODULAR DOOR BIN The door bins are removable for easy cleaning and adjusting. To remove the bin, simply lift the bin up and pull straight out. To replace the bin, slide it in above the desired support button and push down until it stops. FREEZER SECTION ICE BIN 1. To separate the ice bin, pull out the drawer as much as possible. To install, pull out the drawer as much as possible and set the ice bin in its correct position, then push in the drawer. DRAWER w WARNING : Somebody can be hurt if door bins are not firmly assembled. w NOTE : DO NOT adjust a bin that is loaded with food. w CAUTION : DO NOT allow children to play with baskets. Sharp corners on baskets could cause injury. ICE BIN DAIRY BIN 1. To remove the dairy bin, simply lift it and pull straight out. To replace the dairy bin, slide it in above the desired location and push down until it stops. UTILITY BIN Store the utility bin on interior shelf, not on door shelf. w CAUTION : Do not use the utility bin as an ice storage bin in the freezer compartment. [. . . ] If the door is hard to open, wait 5 minutes to allow the air pressure to equalize, then see if it opens more easily. 35 TROUBLESHOOTING GUIDE Check if. . . TEMPERATURE IS TOO WARM OR THERE IS INTERIOR MOISTURE BUILDUP The air vents are blocked. Cold air circulates from the freezer to the fresh food section and back again through air vents in the wall dividing the two sections. Locate air vents by using your hand to sense airflow and move all packages that block vents and restrict airflow. [. . . ]