User manual LG GR-G562JVQ

[. . . ] Keep children away from the unit. 5 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact: x An authorized service center x The dealer from whom you purchased the air conditioner. 7 Do NOT place any blocking objects in front of the unit. 8 If the remote control will not be used for a long time, remove the batteries. [. . . ] x The air conditioner starts up in the Cool mode. 3 You can change modes at any time. To adjust the temperature, press the or buttons on the remote control or unit one or more times until the desired temperature is displayed. The temperature can be set between 64°F and 86°F. Result: x Each time you press the or buttons: ­ The temperature is adjusted by 1°F and displayed on the control panel ­ The unit beeps x The air conditioner starts cooling, if the room temperature is higher than the selected temperature. x If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 To set the fan speed: x Press the , or button on the remote control as desired. or x Press the button on the unit one or more times until the desired Fan speed(F1, F2 or F3) is displayed. Low Medium High 5 To control the direction of the air flow, refer to page 11. E-8 Ventilating Your Room If the air in your room is stale, you can ventilate the room using the Fan feature. 1 If you wish to discharge stale air, push the ventilation lever on the front of the unit to the right and open position ( Result: ). x The air inside the room circulates and stale air is discharged outside. ). Otherwise, push the ventilation lever to the left and closed position ( Result: x The air simply circulates inside the room. 2 If necessary, press the Result: (On/Off) button. Remote Control Control Panel x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. 3 If the fan speed(F1, F2 or F3) is not displayed on the control panel: x Press the button on the remote control or x Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: x The unit beeps each time you press the / button. x The air conditioner starts up in Fan mode. x You can change modes at any time. You can select the Off timer only when the air conditioner operates in the Cool mode. 1 Check that the air conditioner has been switched on; if necessary, press the (On/Off) button. Remote Control Control Panel 2 Set the operating time by pressing the button on the remote control or button on the unit one or more times until the desired time is displayed. The operating time can be set between 1 and 24 hours. Result: x Each time you press the button: ­ The time is adjusted by 1 hour and displayed on the control panel ­ The unit beeps x The operating time is displayed and decreases automatically to indicate the remaining time. You cannot use the Fan mode in the energy saving mode. 2 To stop the energy saving mode, press the control or Result: button on the unit again. button on the remote The fan runs at all times, while the compressor cycles on and off. If you select the Sleep Timer in the Energy Saving mode, the Energy Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode. E-15 Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used. Mode Cooling Indoor Temperature 70°F to 90°F approx. The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. Outdoor Temperature 70°F to 110°F approx. Indoor Humidity 80% or less If the air conditioner is used at. . . Higher temperature Lower temperature Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods. E-16 Cleaning Your Air Conditioner Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time. 1 When cleaning the air conditioner, turn it off and pull out the power plug. Open the front grille by pulling on the tabs of the unit. 2 The removal of the front grille makes it easier to clean the air conditioner. After opening the front grille, lift it up as much as possible, then pull down to release it. Grasp the handle on the air filter and lift it slightly and then out to the front. [. . . ] x Replace the remote control batteries if necessary. x x x x Check that the correct operating mode has been selected(Cool). Dust may be blocking the air filter; refer to page 17 for cleaning instructions. Check that there is no obstacle blocking the air flow into or out of the unit. The air conditioner does not operate with the remote control No beep is heard when you press the (On/Off) button on the remote control The air conditioner does not cool The timer is not correctly triggered Odors are permeating the room during air conditioning x Check that the timer has been programmed correctly; refer to page 12~14. x Ventilate the room. E-18 Technical Specifications Design and specifications are subject to change without notice. [. . . ]