User manual LG GSA-5120D

[. . . ] Use of controls or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Industry Canada requirement This class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC COMPLIANCE STATEMENT Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] * For Optimal 18x writing, 80 pin E-IDE cable and Pentium IV 2. 4GHz or faster are recommended. * Upon the media condition or some of user's enviroment the maximum speed sometimes could not be guarantee. * Occasionally CD-R and CD-RW discs written by a CD-R/RW drive cannot be read by other CD drives*. These unreadable discs may need to be read using the CD-R/RW drive they were created with The disc written using the CD-R/RW drive might not be readable by CD-ROMs other than Multi-read compatible (UDF compatible) CD-ROMs Multiread compatible (UDF compatible) CD-ROMs are: 1. particularly those including Video playback) may require a considerably increased specification PC to give acceptable results. While this Super Multi DVD Rewriter can read DVD-video discs, decoding them to display on your pc's monitor requires separate MPEG decoding that is done by separate hardware (either an MPEG decoder card or MPEG decoding done by your video card), or separate software that you install to do MPEG decoding. For further details, refer to the documentation that comes with MPEG software. 3 Software Install the appropriate CD Recording Authoring Software before using this unit. * Please uninstall any previous CD burning software you may have loaded on your PC in order to prevent possible compatibility issues. Once you have installed the application software, you may (if you wish) begin to reinstall previous software, taking note for errors. We recommend using the drive with the latest software as some problems encountered when using the drive can be solved by updating the software. Location and Function of Controls Front Panel Rear Panel 4 1 23 12 3 4 5 1. Drive activity indicators The LED used to indicate the operation of Super Multi DVD Rewriter. 1. Careful attention is necessary. CS: Cable Select (CSEL) 5 NOTE : Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. Master/Slave setting is determined by jumper installation on the Jumper Connector. The following table shows the possible jumper settings. Name MA (Master) SL (Slave) CS (Cable Select) Function Drive set as Master Drive set as Slave Drive mode set by CSEL on the host IDE interface C S S L M A If you use CSEL setting, the MASTER/SLAVE setting will be made automatically, depending on the hardware configuration. For more details refer to the manual of your computer. PC Connection The Super Multi DVD Rewriter connects to the motherboard of the host computer using an IDE interface cable. You may connect the Super Multi DVD Rewriter as a Slave or Master device, depending on your computer. To Install as a Master Drive To install the drive as a Master, the jumper can be left as supplied from the factory. Master drive (Booting hard disk) Master drive (Super Multi DVD Rewriter) (Jumper left as Master) Master drive (Super Master drive (Booting hard disk) Multi DVD Rewriter) (Jumper left as Master) DIGITAL AUDIO DG DIGITAL AUDIO DG ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 - OR Motherboard Primary connector ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 DIGITAL AUDIO DG ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 Primary connector Slave drive (Other IDE drive) Secondary connector Secondary connector NOTE : A hard disk is normally installed as the Primary Master on the EIDE (ATAPI) interface. Other EIDE peripheral devices such as hard drives and Super Multi DVD Rewriters are then set differently. · If an indicator is displayed on the IDE controller in [Control Panel][System]-[Device Manager]-[Hard Disk Controller], you will need to contact your PC's manufacturer or the motherboard's manufacturer and get the appropriate IDE controller driver. Run Add New Hardware in Control Panel to let PC search again for new device. 8 How to Use the Discs When using CD-ROM discs, CD-R discs, DVD discs or CD-RW discs, don't attach any stickers or labels to the discs. It could cause read and write errors, but data on the disc may be lost due to damage to the disc itself. The Discs in this unit operate at a very high speed! [. . . ] This kind of error is hardly detected from some specific motherboard. · · When you call for service, be prepared to give as much information as possible of your system, environment, and the specific problem. Were there any error messages displayed?etc. ) Please Note: Since this product supports Region Playback Control Phase II, a certain MPEG decoder card or Software without regional code setting may cause this drive not to read DVD-ROM discs. This Drive enables you to change the regional code up to 5 times. [. . . ]