User manual LG GT5142SWES1

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. x Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. x Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. [. . . ] x If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. button one or more times ) 4 Select the fan speed by pressing the until the required setting is displayed: Automatic (rotated : Low Medium High Turbo (maximum) Result: Each time you press the beeps. button, the indoor unit 5 To control the direction of the air flow, refer to pages 16 and 17. If you turn off the air conditioner in Cool mode, the set temperature is adjusted as below when you turn on the air conditioner again. Note Previous set temperature Over 24°C Below 24°C E-10 Set temperature 24°C Previous set temperature Changing the Room Temperature Quickly The Turbo cooling function is used to cool your room as quickly as possible. Example : You have just come home and find that the room is very hot. You wish to cool it down as quickly as possible. The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected. 1 If necessary, press the Result: (On/Off) button. x The air conditioner starts up in Cool mode with Turbo fan speed. x The operation indicator on the indoor unit lights up. x The temperature and fan settings are adjusted automatically. x The air conditioner cools the room as quickly as possible. x After 30 minutes, the air conditioner is reset automatically to the previous mode, temperature and fan settings. But, if you press the button in DRY or FAN mode, it will change to AUTO mode automatically. 2 Press the Result: 3 If you wish to stop the Turbo function before the end of the 30-minute period, press the Result: button again. The air conditioner is reset automatically to the previous mode, temperature and fan settings. 4 To control the direction of the air flow, refer to pages 16 and 17. E-11 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. x Blinking of the timer indicator stops. x The selected mode and the temperature on the display disappear after 10 seconds. x The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On Timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: x The air conditioner will run in the selected mode when it is turned on. To Cancel the On Timer Press the Note (Set/Cancel) button. x If you press the button when the Off Timer is set, the Off Timer is also cancelled. E-18 Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. x Blinking of the timer indicator stops. [. . . ] Note Even if the air conditioner has been switched on via the On/Off switch, operations can still be controlled using the remote control as usual. E-22 Solving Common Problems Before contacting the after-sales service, perform the following simple checks. They may save you the time and expense of an unnecessary call. Problem The air conditioner does not operate at all Explanation/Solution x Check that the breaker used for the air conditioner is switched on. x Check that the operation indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. [. . . ]