User manual LG HMC021M2E9

[. . . ] Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. Do not place any obstacles in front of the unit. [. . . ] This Owner's Instructions is just for using your air conditioner correctly. Thus, the illustrations shown in this manual may not exactly match your air conditioners. The booklet is organized as follows. The following figures are shown on pages 4 and 5: Air conditioning unit (main parts, buttons and display) Remote control (buttons) They will help you find the buttons and understand the symbols displayed. In the manual, you will find a series of step-by-step procedures for each function available. The illustrations in the step-by-step procedures use four different symbols: PRESS PUSH IMPORTANT NOTE Moreover, applicable, wherever the illustrations show the positions of the buttons on both the remote control and the unit itself. Remote control The illustrations have a. . . Example: Unit itself White background. Example: E-6 Inserting the Remote Control Batteries You must insert or replace the remote control batteries when: You purchase the air conditioner The remote control does not work correctly Use two AAA, LR03 . 5V batteries. Do not use old batteries or different kinds of batteries together. Batteries may be completely discharged after months, even if they have not actually been used. Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it. Insert the two batteries, taking care to respect the polarities: + on the battery with + on the remote control - on the battery with - on the remote control Close the cover by sliding it back unitl it clicks into place. Result: You can control all the functions your air conditioning unit directly from your seat, using the remote control. 3 E-7 Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room. You can also set the fan speed. If necessary, press the Result: (On/Off) button. Remote Control Control Panel The air conditioner starts up in the Cool mode. The unit beeps twice. The air is fitted with a protection mechanism to the unit conditioner damaged when it is started immediately prevent from being after being: Plugged in Stopped It will begin to cool after three minutes. Result: Each time you press the or - The temperature is adjusted by °C - The unit beeps The air conditioner starts removing the excess humidity; the quality of air is adjusted automatically. buttons: 4 To control the direction of the air flow, refer to page . E-0 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the right-hand side of the unit, thus increasing the efficiency of the air conditioner. Press the Result: (or on the unit) button on the remote control. Remote Control Control Panel The inner blades swing automatically left and right. In the Energy Saving mode, the blades may stop when the compressor is off. For details on the Energy Saving mode, refer to page 5. To stop the blades moving left and right, press the button on the remote control. (or on the unit) To stop the blades in a specific position and orient the air flow in the corresponding direction, simply press the (or on the unit) button on the remote control when the blades are in the desired position. Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room, you can adjust the orientation of the outer air flow blades on the right-hand side of the unit. RECOMMENDATION When. . . Upwards. Adjust the air flow blades to the desired position, by pushing them upwards or downwards. (The air conditioner operates in the mode selected whe the unit was last used. ) button on the unit. on the remote control or " is displayed. on the unit one or more times until E-3 Selecting Good Sleep Mode The Good Sleep mode can be used when you are cooling your room to switch the air conditioner off automatically after 8 hours. Remote Control Control Panel The Good Sleep function can be set whether the air conditioner is switched on or off, and this function can be selected for any mode. Press the or Press the Result: button on the remote control button on the unit . Each time you press a butoon, the unit beeps. The indicator and " " will be displayed. The remaining time is displayed and decreased by hour automatically to indicate the remaining time. [. . . ] Open the grille as much as possible. 3 4 5 Pull the air filter to the right side. Remove all dust on the air filter with a vacuum cleaner or brush. When you have finished, insert the air filter back into its original position. Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth. [. . . ]