User manual LG HP-C508TA0

[. . . ] · Installation work must be performed in accordance with the National Electric Code by qualified and authorized personnel only. 2 Floor Standing-Type Air Conditioner Safety Precautions Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. E N G LI S H WARNING CAUTION This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage. Meanings of symbols used in this manual are as shown below. Be sure not to do. [. . . ] The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature During softy Dry Operation · The indoor fan speed is automatically set to low and can be set fan speed. 16 Floor Standing-Type Air Conditioner Operating Instructions Heating Operation Mode(Heat Pump Model) E N G LI S H 1 Press the Start/Stop Button. 2 Select heating Operation. Press the Operation Mode Selection Button. Press the heating Operation Button on the remote controller. A/CL 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed. Each time the Button is pressed, the Fan Speed mode is shifted. Owner's Manual 17 Operating Instructions Auto Operation Mode(Cooling Model Only) Press the Start/Stop Button. 1 2 Select Auto Operation. Press the Operation Mode Selection Button. Press Auto Operation Button on the remote controller. A/CL 3 Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level. Cold Cool Proper Warm Hot (This indication will be shifted to the initial Auto Mode Display state after 4 seconds. ) To raise the temperature. (When you feel too cool or cold) To lower the temperature. (When you feel too warm or hot) During Auto Operation · It is impossible to switch the indoor fan speed because of being already set to the best conditioner by fuzzy rule. 18 Floor Standing-Type Air Conditioner Operating Instructions Electric Heater Operation Model(Heat pump&Electric heater) E N G LI S H 1 Press the Start/Stop Button. 2 Select heating Operation by pressing the Opertion Mode Selection button. Press the Heater Operation Button on the remote controller. A/CL A/CL HEATER 3 Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. To raise the temperature To lower the temperature 4 Set the Fan Speed. Each time the Button is pressed, the Fan Speed mode is shifted. Owner's Manual 19 Operating Instructions OFF Timer Setting Procedure(OFF TIMER Setting, or cancel) Press the Start/Stop Button. 1 2 3 Select Function. Press the Timer Button. A/CL · If you press the button, the selected off timer is displayed as follows; · If you select ` ', the Off Timer function will be cancelled. 4 When you finish the Off Timer setting, the Timer indicator lights off. After 4 seconds 5 During off-timer operation if you press the Timer Button, the rest time will be displayed. 20 Floor Standing-Type Air Conditioner Operating Instructions Plasma Air Purifying Operation Procedure(TC* Model) E N G LI S H 1 Air Purifying Operation only Press the Plasma Air Purifying Operation Start/Stop Button. 1 A/CL (Operation will start when the button is pressed, and stop when the button is pressed again. ) 2 Select Fan speed. The display shows low fan speed at the initial condition. Low Mid · You can operate the Plasma Air Purifying under the unit operation of cooling, heating, soft dry or Auto mode. 2 Air Purifying Operation with Cooling or any other Operateion. 1. Press the Plasma Air Purifying Operation ON/OFF Button. Set the fan speed. Owner's Manual 21 Operating Instructions Fan Operation Model(TA*MODEL) 1 Press the Start/Stop Button. 2 Press Fan Operation Button. 3 Set the Fan Speed. MODE Each time the Button is pressed, the Fan Speed mode is shifted. Airflow Direction Procedure 1 Press the Start/Stop Button. 2 Press the Auto Swing Button and then louvers will swing left and right. Press the Airflow Direction Control Button again to set the Vertical louver at the desired airflow direction. (Operation will start when the button is pressed, and stop when the button is pressed again. ) The vertical louver swing left and right. The horizontal louver swing up and down. 22 Floor Standing-Type Air Conditioner Operating Instructions Jet Cool Operation 1 Press the Start/Stop Button. On/Off 2 Press the Jet Cool button to operate the speed cooling mode and the unit will operate in high fan speed on cooling mode. (Z, H/P Model) (C/O Model) 3 To cancel the Jet Cool mode, press the Jet Cool button again or the fan speed button or the room temperature setting button and the unit will operate in mid fan speed on cooling mode. or or NOTE: During the JET COOL function at any moment, the A/C starts to blow the cool air at extremely high speed setting the room temp. It is especially used to cool the room temp. In heat pump mode or neuro fuzzy mode however, the JET COOL function is not available. In order to return to the normal cooling mode from the JET COOL mode, you just press either the operation mode selection button, airflow volume selection or temp. setting button or the JET COOL button again. Owner's Manual 23 Operating Instructions Child Lock Operation Procedure Press the fan speed button and High temperature setting buttons simultaneously for 3 seconds. The unit will respond with beep. 1 After 3 second, it will shift After 3 seconds, it will shift 2 During Child Lock Operation Whenever you press any Button on Display Panel, it will immediately display " ", which means Display panel is Locked. All the Button on the indoor unit Display panel will not work. [. . . ] In order to prevent this, the airflow will not begin until it is sufficiently warm. · The room may have been very hot when the room air conditioner was first turned on. · Has the temperature been set incorrectly?· Are the indoor unit's air inlet or outlet vents obstructed? [. . . ]