User manual LG HS-C096ZR63

[. . . ] 11 Because the rear of air conditioner is very sharp, please put gloves on when carrying or installing the air conditioner. 12 Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor. CAUTION The manufacturer does not assume responsibility for accidents or injury caused by an incorrectly installed air conditioner. If you are unsure about installation, contact an installation specialist. E-2 Contents x PREPARING YOUR AIR CONDITIONER s s s Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description of Each Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. 81°F ~ 84°F 73°F ~ 64°F 3 To control the direction of the air flow, refer to page 7. E-6 Ventilating Your Room If the air in your room is stale, you can ventilate the room using the Fan feature. 1 If you wish to discharge stale air, push the ventilation switch on the front of the unit to the right and open position( ). Result: x The air inside the room circulates and stale air is discharged outside. ). Otherwise, push the ventilation switch to the left and closed position( Result: x The air simply circulates inside the room. 2 Turn the SELECTOR and set it to "HI FAN" or "LOW FAN" position. Result: Note x The air conditioner starts up in fan mode. x You can change modes at any time. 3 To control the direction of the air flow, refer to the section below. Adjusting the Air Flow Direction Horizontally The air flow direction blades can be adjusted to improve the efficiency of the air conditioner. 1 The side by side air direction louvers are together and are controlled by a lever. They regulate air discharge to the right, left or straight. E-7 Power Failure Here are a few recommendations that you should follow when using your air conditioner. If a power failure occurs, set the SELECTOR to OFF. When the power comes back on, wait five minutes before turning the unit back on. Temperature and Humidity Range The following table indicates the temperature and humidity ranges within which the air conditioner can be used. Higher temperature Lower temperature Then. . . The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. Mode Indoor Temperature Outdoor Temperature 70°F to 110°F approx. Indoor Humidity 80% or less If the unit is used for long periods at a high humidity level, water may condense on and drip from the surface of the air conditioner. Cooling 70°F to 90°F approx. E-8 Cleaning Your Air Conditioner Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time. IMPORTANT When cleaning the air conditioner, turn it off and pull out the power plug. 1 Hold the air filter handle, pull it slightly forward, and then pull it out to the right side. 2 Remove the dust on the air filter using a vacuum cleaner and brush. 3 Insert the air filter back into its original position. 4 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth. x Do not, under any circumstances, cut or remove the third grounding prong from the power cord. x We recommend that you do not use an extension cord or an adapter plug with this appliance. x Do not change the plug on the power cord of this appliance. x Follow national electrical codes or local codes and ordinances. 115V 15 AMP circuit "parallel" type 230V/208V 20 AMP circuit "perpendicular" type 230V/208V 15 AMP circuit "tandem" type 230V/208V 30 AMP circuit "tandem" type x If the electric supply provided does not meet the above specifications, call a licensed electrician. x Aluminum house wiring may pose special problems - consult a qualified electrician. x This unit requires a separate circuit, serving only this appliance. 2 Window Requirements x Standard double-hung window with actual opening width of 22" to 36". The installation will need to be modified for windows other than the standard double-hung type. 22" to 36" 12 7/8" min x Clear vertical opening of 12 7/8" minimum, from bottom of sash to sill. x Install the air conditioner in a window where there will be enough clearance around the cabinet to allow ample circulation of air through the unit. Note All supporting parts should be secured to firm wood, masonry or metal. E-12 Window installation Tools needed x Philips head screwdriver x Adjustable wrench x Scissors Parts furnished Type A Screw (4X10) B Window bracket C Name of part Long wood screw (5X16) x Ruler or tape measure x Pencil Q'ty Type 7 D 1 Install the top support channel with three Type B screws provided. ;;;; ;;; Name of part Q'ty 1 Top support channel 9 E 2 F Type G Name of part Window filler panel(Right) Q'ty 1 Note The screw holes are larger gauge on the channel and smaller on the cabinet. The top support channel is "L" shaped. The high side of the channel must always face inwards. ;;;; Adhesive seal strip Window gasket Window filler panel(Left) H 1 1 1 Top support channel 2 Assemble the window brackets on the cabinet. 2-1 Loosen the lower screw slightly on each side of the cabinet and install the Type C window bracket. [. . . ] Note After several minutes the unit will be blowing out cold air. All replaced parts and products become the property of LG and must be returned to LG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following, including, but not limited to: delivery and installation; damage which occurs in shipment; applications and uses for which this product was not intended; failures or problems which are caused by products or equipment not supplied by LG; accidents, misuse, abuse, neglect, misapplication, fire, water, lightning or other acts of nature; incorrect electrical line voltage, fluctuations or surges; damage caused by improper or faulty installation; product alteration or modification; improper or unauthorized repair; cosmetic damage or exterior finish; product with altered serial numbers; failure to follow operating and environmental instructions that are covered and prescribed in the instruction book; customer adjustments, routine maintenance and cleaning; consumable items such as filters; use of non-LG or unauthorized parts, supplies, accessories or equipment which damage this product or result in service problems. [. . . ]