User manual LG HSNC2463R70

[. . . ] The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademark Recognition Kensington is a U. S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world. All other product names used in this manual are the properties of their respective owners and are acknowledged. --i-- DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. [. . . ] Push the MENU button to exit the dialog box. 6. The password confirm menu appears when user presses the power-on key in case the Security Lock is enabled. Enter the password in the order you set it at step 5. In case you forget the password, please contact the service center. Service center will validate the owner and help reset the password. ­ 14 ­ DLP Projjecttor ­ User''s Manuall DLP Pro ec or ­ User s Manua Adjusting the Projector Level Take note of the following when setting up the projector: · · · The projector table or stand should be level and sturdy. Position the projector so that it is perpendicular to the screen. Ensure the cables are in a safe location. You could trip over them. 1. To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B]. The height adjuster drops down [C]. 2. 3. To lower the level of the projector, press the height-adjuster button and push down on the top of the projector. To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the desired angle has been achieved. ­ 15 ­ DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua Adjusting the Zoom, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the projected image and screen size B . 2. Use the Image-focus control (on the projector only) to sharpen the projected image A . 3. Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect. Remote control and OSD panel 4. The keystone control appears on the display. ­ 16 ­ DLP Projjecttor ­ User''s Manuall DLP Pro ec or ­ User s Manua Adjusting the Volume 1. Press the Volume +/buttons on the remote control. The volume control appears on the display. 2. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/-. 3. Press the MUTE button to turn off the volume (This feature is available only on the remote). ­ 17 ­ ON-SCREEN DISPLAY (OSD) MENU SETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector. 1. (Range: Auto ­ RGB ­ YPbPr- YCbCr) Press the cursor button to adjust the color temperature. (Range: 6800 °K ~ 10500 °K) (Enter) / to enter the color manager menu. (Range: Red-Green-Blue-CyanPress Magenta-Yellow-White). See page 24 for more information on Color Manager. ­ 23 ­ DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua Color Manager Press (Enter) / to enter the Color Manager sub menu. ITEM Red Green Blue Cyan Magenta Yellow White DESCRIPTION Select to enter the Red Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain. Select to enter the Green Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain. Press the buttons to adjust the Hue, Saturation, and Gain. Press the buttons to adjust the Hue, Saturation, and Gain. Select to enter the Magenta Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain. [. . . ] Power surges can cause the lamp to turn off. When the Ready LED is on, press the power button. Put the old lamp back in the projector and have the projector serviced. Remote Control Problems Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on the projector. [. . . ]