User manual LG IPS231B

[. . . ] ENGLISH OWNER'S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODEL IPS231P IPS231B www. lg. com Safety Precautions Please read these safety precautions carefully before using the product. Warning Failure to follow those warnings may result in death, serious injury or damage to the product or other property. Electrical Power Related Precautions Warning Use only the power cord supplied with the unit or another manufacturer authorized cord. - Failure to do so may result in fire or electrical shock or damage to the product. Use only a properly grounded plug and receptacle. - If you do not you may be electrocuted or injured. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and the receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces. 4 Accessories !!!Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards Power Cord DVI-D Signal Cable (This feature is not available in all countries. ) 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) Audio Cable NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. 5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices are turned off. Connecting the stand base or Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Assemble the Stand Base into the Stand Body. Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. Stop Pin Stand Body Stand Base WARNING The tape and locking pin may only be removed from those monitors equipped with a standing base when the base is pulled up. Otherwise, you may be injured by the protruding sections of the stand. Product Handling with Care : When you lift up or move the product, Do Not hold or touch the front part of LCD panel. (Please hold the Stand Body or plastic cover of the product. ) 6 Connecting the Display 3. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 4. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. 5. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise. IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Positioning your display After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Swivel Range : 356° 7 Connecting the Display Height Range : maximum 4. 33 inches (110. 0 mm) 110. 0 mm * Please be sure to remove the Locking pin to adjust the height. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. [. . . ] If yes, readjust the video card to the recommend resolution. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. [. . . ]