User manual LG JVM1533BD-005

[. . . ] Connect Function Scheduler cable to Function Scheduler installation board as shown in the right picture. 12V SIG GND Red wire Yellow wire Black wire 12V SIG GND Red Yellow Black Function Scheduler cable Function Scheduler cable is connected as factory default. 2. After fixing the cable to the guide slot, attach Function Scheduler installation board at the desired location. Before fixing Function Scheduler cable to the guide slot, remove any clogged part of the case in the direction to install before the installation. <Front side of installation board> <Rear side of installation board> Guide slot 3. After locating Function Scheduler installation board at the desired location, screw the unit firmly. [. . . ] Press the button to turn on all connected indoor units. Press the button to turn off all connected indoor units. Selection of Indoor Unit 1. This is the function to confirm which indoor's condition is displayed in Function Scheduler. Press the button, then corresponding unit's LED blinks for 5 seconds. It displays the number of indoor units for a moment which has reserved schedule(s). EX) The number of schedule-set indoor units : 16 NOTE If you set a schedule after selecting a group or all indoor units, the number can be bigger than the number of actually connected indoor. Owner's & Installation Manual 11 Owner's Instruction Cooling Operation To run a indoor unit in Cooling mode 1 2 Select a indoor unit at central controller and press the Function Scheduler. button to change cooling operation mode of In Cooling Mode, Temperature can be set between 18 C and 30 C. Temperature increases 1C by pressing the button once. Temperature decreases 1C by pressing the button once. 3 To change Operation Mode, Press Cooling Auto Dehumidification button. Operation Mode is changed as following sequence Heating Fan. 12 Function Scheduler Owner's Instruction Heating Operation ENGLISH To run a indoor unit in Heating mode 1 2 Select a indoor unit at central controller and press the Function Scheduler. button to change cooling operation mode of In Heating Mode, Temperature can be set between 18 C and 30 C. Temperature increases 1C by pressing the button once. Temperature decreases 1C by pressing the button once. 3 To change Operation Mode, Press Heating Fan Cooling Auto button. Operation Mode is changed as following sequence Dehumidification. Owner's & Installation Manual 13 Owner's Instruction Dehumidification / Fan Operation To run a indoor unit in Dehumidification mode 1 Set the Dehumidification mode by pressing the button after selecting the indoor unit. You can perform effective dehumidification operation and cooling operation at the same time if using this function in rainy season or much humidity. It is impossible to control temperature for dehumidification operation. To run a indoor unit in Dehumidification mode 1 Set the Dehumidification mode by pressing the button after selecting the indoor unit. During fan operation, general fan wind comes out, not cold wind. fan speed : Select desired fan speed by pressing button. desired temperature : Select desired temperature by pressing button. to set 13 If you wantbutton schedule1 Only, press to confirm Schedule 1. At the scheduled day of week, the border appear like . * The border means that corresponding day of week has a programmed schedule. 24 Function Scheduler Owner's Instruction Hour' setting 14 Enter `On Time pressing mode of Schedule 2 by button. The `On Time Hour' segment of Schedule 2 will blink, Schedule 1 will be not displayed. ENGLISH 15 Set Schedule 2 by repeating (4) ~ (12). Press 16 setting. button to confirm `Schedule' At the scheduled day of week, the border appear like . To cancel the scheduling during above process, press Button, then setting schedule is canceled and previously set schedule will be reloaded. Owner's & Installation Manual 25 Owner's Instruction Programming : Schedule Priority If two schedules are setup at same time, it operates higher priority schedule. the 1 If are schedule time of Schedule 1 and 2 same, the schedule time of Schedule 1 has higher priority than Schedule 2. EX) In case of the same schedule time of Schedule 1 and 2, as the schedule time of Schedule 1 has higher priority than Schedule 2, corresponding indoor unit will stop the operation at AM 11:00. 2 In same schedule, Off Time is higher priority than On Time. EX) In same schedule, because Off Time is higher priority than On Time , corresponding indoor unit will stop the operation at AM 9:00. On schedule setting mode, if you don't input anything, it will get out in `Schedule' setting mode in a few seconds. 26 Function Scheduler Owner's Instruction TIPS It is possible to set scheduler in off operation condition. ENGLISH Off condition It is able to select a unit without change its condition by pressing the individual On/Off button twice. Individual On/Off button NOTE At schedule time setting, please make OFF TIME be later than ON TIME Otherwise, it can cause abnormal behavior. EX) If users set On time at AM 11:00 and Off time at AM 9:00, the scheduled indoor unit will be stopped at AM 9:00 and will be operated at AM 11:00. This operation can be different from the user's intention. [. . . ] Then Function Scheduler will display (all indoor units selection) icon. 2 Press and button at same time. After a while (about 15~20 seconds), icon will blink for about 3 seconds and total schedule of all indoor unit is deleted. 32 Function Scheduler Owner's instruction Programming : Schedule Copy ENGLISH To apply a schedule to other days (Example. To make a the schedule of Monday be same with Tuesday's one, use schedule copy/paste function. ) indoor 1 Select desired central unit to set by schedule(s) in controller pressing the individual On/Off button. to enter `Schedule' The previously scheduled day of week icon will blink. week 3 Select the day ofbutton. [. . . ]