User manual LG JVM1542WF-03

[. . . ] It may cause product breakdown. If the product was submerged under water, ask the service center for instruction. It may cause fire or an electric shock unless you do that. v Ser ice Cen ter CAUTION Make sure children or senor citizens use the product under proper observation in order to prevent safety accident. Do not pick the product with a sharp tool. It may cause product breakdown with the damage to its parts. I In-use Do not clean the product with strong cleanser such as solvent. [. . . ] Use the sensor with the lower temperature between the remote controller and the product Ceiling height selection switch 1. High ceiling Group control switch 1. For group control use 123 12 * When changing the product selection switch and group control switch, the power must be reconnected to reflect the changes. Owner's & Installation Manual 7 Installation Method Installation Method 1 Put the installation paper on the place and determine the position and height of the fixing screws of the wired remote controller. · Refer to the printed side of the installation paper. The position of the fixing screws 2 Plug the connecting cable into the indoor unit. · The product is being shipped with the cable connected only to the remote controller. Put each cable to the remote controller according to the color match Be careful not to alter the colors of the remote controller connection cables. Main frame CN-M C CN-ZONE CN-DISP IC01A C01K J14 Red Yellow Brown Side of remote Controller Side of Indoor Unit Fixing the remote controller Fixing the connecting cable 3 Remove the installation paper before installing the remote controller so that it can fit into the right place. * When installing the wired remote controller, do not install it so that it is buried to the wall. (This can cause error in the temperature sensor) * When installing multiple wired remote controllers vertically in one location, leave a minimum distance apart (5cm). (This can cause error in the temperature sensor) * Do not install the cable with a distance of 30 m or longer. (This can cause communication error. ) * When installing the cable, check whether the connector between the remote controller and the product is installed properly. The connector will not be connected when installed in opposite sides. Supply the power after connecting wired remote controller. · If you press the fan speed button, the strength of the fan speed will change in the order of Low ¡ Medium Hi ¡ Power. · If the product is not compatible with the fan speed control, it will not function as your selection. Fan Speed Selection in Cooling Operation Lo Med Hi Po Fan Speed Selection in Heating, Dry, Fan, Auto-Operation Lo Med Hi · If the indoor unit is compatible with the slo fan speed, you can adjust the air flow slow level. 16 Deluxe Wired Remote Controller Sub Function Sub Function Auto Swing You can control the wind direction easily. 1 2 Press the Sub function button on the remote controller. Press the automatic Auto Swing button. 3 A click of Auto Swing button will turn on/off the indicator. * If the product is not compatible with the automatic wind direction mode, it will not operate automatically. Owner's & Installation Manual 17 Sub Function Plasma You can use the plasma function. 1 2 Press the Sub function button. Press the Plasma button. · A click of the Plasma button will turn on/off the indicator. · If the product is not compatible with the Plasma function, it will not do the Plasma function even though the indicator is turned on. Power Saving You can use the power-saving function. 1 Press the Sub function button. 2 Press the power-saving button. · A click of the power-saving button will turn on/off the indicator. · If the product is not compatible with the power-saving function, it will not do the function. 18 Deluxe Wired Remote Controller Sub Function Ventilation You can use the ventilation function. 1 2 Press the Sub function button of the remote controller. Press the ventilation button. · A click of the ventilation button will turn on/off the indicator. However, even when the remote controller that does not have the ventilation function displays ventilation, the actual product does not operate for ventilation. Heater You can use the heater function. 1 2 Press the Sub function button. Press the heater button. · A click of the heater button will turn on/off the indicator. · If the product is not compatible with the heating function, it will not do the heating function. Owner's & Installation Manual 19 Special Function Special Function This is a function to prevent tampering of settings by children or others. Child Lock You can use the child lock function. 1 2 Press the Special Function button of the remote controller. Press the child lock button. · A click of the child lock button will turn on/off the indicator. · If you press another button while adjusting child lock function, the temperature display will show CL for three seconds and then the operation will come back to the original mode. · If you want use the child lock function in standby mode, select child lock and press the On/Off button within three seconds. Then the standby mode will change into the child lock mode. · If you want to cancel the child lock function in the standby mode, just press the child lock button. 20 Deluxe Wired Remote Controller Special Function Vane control You can control the angle of the vane. 1 2 3 4 5 6 Select the Advanced Selection button on the control panel of the remote controller. Press the Vane Control button one more time to control the top and bottom vane. [. . . ] Then you can choose the proper day in the order of Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, and Sunday. 3 If you press the hour/minute selection button, the hour digits will flash so that you can adjust it by pressing the temperature control button. If you press the hour/minute button one more time, the minute digits will flash. You can adjust it by pressing the temperature control button. After adjusting time, press the setting button so that the current configuration can be saved. 4 24 Deluxe Wired Remote Controller Special Function Weekday reservation Weekday reservation is the function to set the time to turn on and off for each day during the week from Monday through Sunday. 1 2 3 4 5 6 Press the Reservation Mode button on the control panel of the remote controller. [. . . ]