User manual LG L1510BF

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Disposal of this product must be carried out in accordance to the regulations of your local authority. A3 Connecting the Display Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. Assemble the stand base into stand body in the correct direction as shown in the picture, then tighten the screw which is attached to the stand base. Stand Body Stand Base Screw 3. Once assembled take the monitor up carefully and face the front side. Disassembling the stand 1. Place the monitor face down on the cushion or soft cloth. Loosen the screw which is attached to the stand base, then take off the stand base from stand body. Stand Body Stand Base Screw Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5°~17° Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect DVI-D Cable B Connect D-sub Cable (PC) C Connect D-sub Cable (Mac) D Connect HDMI Cable NOTE This is a simplified representation of the rear view. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A10 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu EZ ZOOMING 4:3 IN WIDE NORMAL Sub-menu RD H Reference To adjust the resolution To adjust the image size PHOTO EFFECT CINEMA MODE VOLUME TIME CONTROL PICTURE GAUSSIAN BLUR SEPIA MONOCHROME To adjust screen color mode To focus on the moving picture selected. To adjust the volume To mind user using time. BRIGHTNESS CONTRAST GAMMA **BLACK LEVEL PRESET sRGB 6500K 9300K To costomize the color of the screen To adjust the brightness, contrast and gamma of the screen To set offset level COLOR RED GREEN BLUE HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS LANGUAGE HORIZONTAL VERTICAL *WHITE BALANCE **OVERSCAN RTC POWER INDICATOR FACTORY RESET OSD POSITION MOVIE *INTERNET **GAME USER *NORMAL **STANDARD *DEMO **SPORTS G To adjust the position of the screen TRACKING To improve the clarity and stability of the screen SETUP To costomize the screen status for a user's operating environment FLATRON F-ENGINE To select or customize desired image settings : Adjustable * : only for D-sub/DVI Input ** : only for HDMI Input R : DSUB Input D : DVI Input H : HDMI Input NOTE The order of icons may differ depending on the model (A11~A19 ). A11 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Icons Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A12 On Screen Display(OSD) Selection and Adjustment Main menu PICTURE Sub menu Description PICTURE DSUB/DVI input BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. [. . . ] Check the signal cable and try again. Do you see a "OSD LOCKED" message on the screen? G Do you see "OSD LOCKED" when you push MENU button?· You can secure the current control settings, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message "OSD UNLOCKED" will appear. A20 Troubleshooting Display image is incorrect G Display Position is incorrect. · Press the AUTO/SET button to automatically adjust your display image to the ideal setting. [. . . ]