User manual LG L173ST

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] The product may fall and get damaged or injure your foot. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° Swivel Range : 350° Height Range : maximum 3. 94 inch (100. 0mm) 100. 0mm * Please be sure to remove the Locking pin to adjust the height. Ergonomic You do not need to replace the Locking pin after it is removed, to adjust its height. It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect signal cable 1 and power cord 2 in order, then tighten the screw of the signal cable. A Connect D-sub Cable (PC) B Connect D-sub Cable (Mac) C Connect DVI-D Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. Power Cord 2 1 Signal Cable Varies according to model. Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. Wall-outlet type PC MAC PC DVI-D(This feature is not available in all countries. ) 2. Touch the power button on the front of panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power button NOTE 'Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. The message "OSD UNLOCKED" should appear. A9 Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A17. (SOURCE Hot key) Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always touch the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 26 inch monitor : 1920 x 1200 Power Button Use this button to turn the display on or off. Power Indicator This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. A10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: Touch the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, touch the AUTO/SET Button. [. . . ] 'Specifications' section of this manual and configure your display again. G Do you see a "CHECK SIGNAL CABLE" message on the screen?· This message appears when the signal cable between your PC and your display is not connected. Check the signal cable and try again. Do you see a "OSD LOCKED" message on the screen? G Do you see "OSD LOCKED" when you push MENU button? [. . . ]