User manual LG L1752S-BF

[. . . ] Use the screws to secure the stand on the rear side of the product as shown in the diagram. 1 Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. After installing your speakers, use holders and cable ties to organize the speaker cables. Cable holder Remove the paper. * This feature is not available in all model. When the speaker is installed. Cable tie *Connect the input terminal with a proper color match. * This feature is not available in all model. 2 To install Portrait - Only on some models. "When installing Portrait, rotate it clockwise based on its front. " 3 Using the Remote Control Name of the Remote Control Buttons · AV Button · Power On/Off Button · Input Select Button (See next page) · ARC button Aspect Ratio Correction. · Auto Button Automatic adjustment function (Operational for the analog signal only) There is not a function which is supported · Sleep Button When watching AV, RGB PC, HDMI/DVI , Component1, Component2 The product will be automatically turned off after a certain period of time. Press this button repetitively to select an appropriate time duration · PSM Button - Toggles through preset video settings. 1 4 7 2 5 8 0 3 6 9 There is not a function which is supported There is not a function which is supported · Menu Button · UP and Down buttons Bring up and down direction adjustment. · Exit Button · Volume Button Volume up and down · Check Button · Mute button * There is not a function which is supported 4 Using the Remote Control · AV Button Toggles through video AV Component1 Component2 RGB PC HDMI/DVI · Input Select Button If you press the button once, the following Input Signal Window will appear. [. . . ] and SW version. Information Set ID Serial No. SW Version MENU Set ID You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display. Specify the number (1~99) using the button and exit. Use the assigned Set ID to individually control each product using the Product Control Program. This menu shows the serial number of the product. This menu shows the software version. Serial No. SW Version 31 Troubleshooting No image is displayed G Is the product power cord connected?· See if the power cord is properly connected to the outlet. · See if the power switch is turned on. · May need service. G Power is on, power indicator is blue but · Adjust brightness and contrast again. · If the product is in power saving mode, move the mouse or press any key. If adjustment is not satisfactory, use the Phase OSD menu. · The proper input signal is not connected to the signal port. Connect the signal cable that matches with the source input signal. G Do thin lines appear on the background screen? G Horizontal noise appears or the characters look blurred. G The screen is displayed abnormally. After-image appears on the product. G After-image appears when the product is turned off. · If you use a fixed image for a long time, the pixels may be damaged quickly. Use the screen-saver function. 33 Troubleshooting The audio function does not work. G No sound?· See if the audio cable is connected properly. · See if the sound is set properly. · Select the appropriate equalize sound. G Sound is too low. Screen color is abnormal. G Screen has poor color resolution (16 colors). · Set the number of colors to more than 24 bits (true color) Select Control Panel ­ Display ­ Settings ­ Color Table menu in Windows. · Check the connection status of the signal cable. [. . . ] Transmission [f][a][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] 0 : Monday 1: Tuesday 2 : Wednesday 3 : Thursday 4 : Friday 5 : Saturday 6 : Sunday [Data2] 0H~17H (Hours) [Data3] 00H~3BH (Minutes) Acknowledgement [a][][Set ID][][OK/NG][Data1][Data2][Data3][x] *When reading data, FFH is inputted for [Data1], [Data2] and [Data3]. In other cases, all are treated as NG. L A19 RS-232C Controlling the Multiple Product Transmission / Receiving Protocol 33. On Timer (On/Off Timer) On, Off (Command : F b) Set days for On Timer. Transmission [f][b][][Set ID][][Data1][][Data2][Cr] [Data1] 0 (Write), FFH(Read) [Data2] 00H~FFH bit0 : Monday On Timer On(1), Off(0) bit1 : Tuesday On Timer On(1), Off(0) bit2 : Wednesday On Timer On(1), Off(0) bit3 : Thursday On Timer On(1), Off(0) bit4 : Friday On Timer On(1), Off(0) bit5 : Saturday On Timer On(1), Off(0) bit6 :Sunday On Timer On(1), Off(0) bit7 : Everyday On Timer On(1), Off(0) Acknowledgement [b][][Set ID][][OK/NG][Data1][Data2][x] 34. [. . . ]