User manual LG L1752T

[. . . ] If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation. Please use approved power cord provided by Philips all the time. If your power cord is missing, please contact with your local service center. (Please refer to Customer Care Consumer Information Center) Do not subject the LCD monitor to severe vibration or high impact conditions during operation. [. . . ] Other combinations of lit and dark sub pixels appear as single pixels of other colors. Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is, a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are three types of bright dot defects: file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20. . . . 00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/product/pixel. htm (1 of 3)2006-12-4 15:17:14 Philips Pixel Defect Policy One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple Three adjacent lit sub pixels - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) (one white pixel) A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots. Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern. There are two types of black dot defects: One dark sub pixel Two or three adjacent dark sub pixels Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables. BRIGHT DOT DEFECTS MODEL ACCEPTABLE LEVEL 190CW7 file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20. . . . 00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/product/pixel. htm (2 of 3)2006-12-4 15:17:14 Philips Pixel Defect Policy 1 lit subpixel 2 adjacent lit subpixels 3 adjacent lit subpixels (one white pixel) Distance between two bright dot defects* Total bright dot defects of all types 3 1 0 >25mm 3 BLACK DOT DEFECTS MODEL 1 dark subpixel 2 adjacent dark subpixels 3 adjacent dark subpixels Distance between two black dot defects* Total black dot defects of all types ACCEPTABLE LEVEL 190CW7 5 2 0 >15mm 5 TOTAL DOT DEFECTS MODEL Total bright or black dot defects of all types Note: * 1 or 2 adjacent sub pixel defects = 1 dot defect Your Philips monitor is ISO13406-2 Compliant ACCEPTABLE LEVEL 190CW7 5 RETURN TO TOP OF THE PAGE file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20. . . . 00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/product/pixel. htm (3 of 3)2006-12-4 15:17:14 Installing Your LCD Monitor Installing Your LCD Monitor · Front View Produt Description · Connecting to Your PC · The Base · Getting Started · Optimizing Performance Front View Product Description 1 2 3 4 5 6 AUTO MENU To switch monitor's power On and Off To access OSD menu / to confirm To move and adjust To adjust brightness of the display To adjust contrast of the display Automatically adjust the horizontal position, vertical position, phase and clock settings. RETURN TO TOP OF THE PAGE <> file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20d. . . 00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/install/install. htm (1 of 3)2006-12-4 15:17:15 Installing Your LCD Monitor Rear View 1 2 3 4 Kensington anti-thief lock AC power input DVI-D input VGA input RETURN TO TOP OF THE PAGE Optimizing Performance q For best performance, ensure that your display settings are set at 1440 x 900, 60Hz. Note: You can check the current display settings by pressing the 'MENU' button once. The current display mode is shown in OSD main controls called RESOLUTION. q You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance out of your monitor. Step-by-step instructions are provided to file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20d. . . 00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/install/install. htm (2 of 3)2006-12-4 15:17:15 Installing Your LCD Monitor guide you through the installtion process. Select the 'Settings' tab then click on 'Advanced. . . '. Select 'Monitor' - If the 'Properties' button is inactive, it means your monitor is properly configured. - If the 'Properties' button is active. Click on 'Driver' and then click on 'Update Driver. . . ' then click on the 'Next' button. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on 'Next' and then click on 'Have disk. . . '. Click on the 'Browse. . . ' button then select the appropriate drive F: ( CD-ROM Drive). Click on the 'Open' button, then click on the 'OK' button. Select your monitor model and click on the 'Next' button. Click on the 'Finish' button then the 'Close' button. If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button. 6. 11. For Windows® Me Start Windows® Me Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. [. . . ] The controller provides the interface registers to allow communication to/from the host. Hub specific status and control commands permit the host to configure a hub and to monitor and control its ports. Device A logical or physical entity that performs a function. The actual entity described depends on the context of the reference. [. . . ]