User manual LG L1760SR

[. . . ] User's Guide L1760SR Make sure to read the Important Precautions before using the monitor. Keep the User's Guide(CD) in an accessible place for furture reference. See the label attached on the monitor and give the information to your dealer when you ask for service. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] Once you connect the stand base, try not to disconnect it. Do not carry the monitor upside down holding only the stand base. The monitor may fall and get damaged or injure your foot. A3 Connecting the Display To attach or separate the back cap 1. To attach the back cap, fix into the 3 holes first then slide it up to fit to the upper groove. Back Cap NOTE - Cover the back cap after connecting the cables before use. (To connect the cable, see page A5 for reference. ) 2. To separate the back cap, hold the bottom part and pull it out. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores A4 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. When attached, tighten the thumbscrews to secure the connection. Connect the power cable 3 with the AC-DC adapter (AC-DC power supply) 2 , and then plug the cable in the outlet. 2. Connect the signal cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. DC-IN D-SUB [ Arranging the cables] 3 DC-IN D-SUB 2 Wall-outlet type PC PC-outlet type 1 [ Connecting the cables] Mac adapter PC MAC For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 4. Touch the pawer button in front to turn on the monitor. The 'Self Image Setting Function' will automatically run when the monitor is on. NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the SET/AUTO function button to improve resolution. A5 Control Panel Functions Front Panel Controls Side MENU Engine SET/AUTO Control MENU Button Function Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. + - Buttons - Button ( ) Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A13. A6 Control Panel Functions Control SET/AUTO Button Function Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the SET/AUTO button before entering the On Screen Display(OSD). [. . . ] You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message "OSD UNLOCKED" will appear. A14 Troubleshooting Display image is incorrect G Display Position is incorrect. · Press the SET/AUTO button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. · Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. [. . . ]