User manual LG L177WSB-PFS

[. . . ] Make sure to keep the package box for transporting the product in the future. Unpacking Introduction PDP Display Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide Cables Power Cord Others Remote Control Batteries (AAA X 2) (Not available in all locations) Ferrite Core for Power Cord Sold separately D-Sub Cable DVI Cable Wall Mount KIT Semi Stand KIT (Applicable to the model only) BNC Cable BNC to RCA Adaptor Jack To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions. Ferrite Core (Power Cord) Introduction · · The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug. Your PDP Display Front SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the time. [PC] [DVI] [AV] [HDMI] [Component] [BNC] Enter button [ ] Activates a highlighted menu item. MENU button [MENU] Opens the on-screen menu and exits from the menu. [. . . ] - This fuction does not work for this PDP Display. Connections Connecting a Computer Using a Power cord with Earth · In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the PDP Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your PDP Display. Connect the power cord for your PDP Display to the power port on the back of the PDP Display. There are 2 ways to connect the D-sub to your PDP Display. Choose one of the following: Using the D-sub (Analog) connector on the video card. · Connect the D-sub to the 15-pin, RGB port on the back of your PDP Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. · Connect the DVI Cable to the DVI(HDCP) port on the back of your PDP Display and the DVI port on the computer. Using the BNC (Analog) connector on the video card. Connections · Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V ports on the back of your PDP Display and the 15 pin D-sub Port on the computer. Connect the audio cable for your PDP Display to the audio port on the back of your computer. Note · · · Turn on both your computer and the PDP Display. Contact a local LG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth · In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. You cannot connect a PC to the HDMI IN terminal. Connecting Using a DVI Cable Note · · Connect the DVI output terminal of a digital output device to the DVI IN terminal of the PDP Display using a DVI cable. Set the name of DVI input to AV device in Source -> Edit Name Menu. Connections Connecting to an Audio System Note · Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT [L-AUDIO-R] on PDP Display. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the PDP Display. Unplug the video cable from the back of the computer. Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. (Do not exceed 60Hz when using the maximum resolution. ) 5. If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel -> System -> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver. Check List Note · The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Problems related to the Installation (PC Mode) Note Problems related to the PDP Display installation and their solutions are listed. Q: The PDP Display screen flickers. Troubleshooting A: Check if the signal cable between the computer and the PDP Display is securely connected. [. . . ] (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Check the volume level. If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: A: The remote control buttons do not respond. [. . . ]