User manual LG L1804RYT

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Place the monitor with its front facing downward on a soft cloth. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it "click". Stand Body REAR 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Once assembled take the monitor up carefully and face the front side Stand Body Stand Base REAR REAR FRO NT REAR FRO NT Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Once you connect the stand base, try not to disconnect it. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A3 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° 20 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A4 Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. When attached, tighten the thumbscrews to secure the 3. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A8 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu PICTURE Sub menu BRIGHTNESS CONTRAST GAMMA COLOR PRESET 6500K 9300K RED GREEN BLUE POSITION HORIZONTAL VERTICAL TRACKING CLOCK PHASE SHARPNESS SETUP LANGUAGE OSD HORIZONTAL POSITION VERTICAL Reference To adjust the brightness, contrast and gamma of the screen To customize the color of the screen To adjust the position of the screen To improve the clarity and stability, sharpness of the screen To customize the screen status for a user's operating environment WHITE BALANCE POWER INDICATOR FACTORY RESET F-ENGINE MOVIE / TEXT USER NORMAL To select or customize desired image settings : Adjustable NOTE The order of icons may differ depending on the model (A9~A13). A9 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name PICTURE Icons Sub-menus Button Tip MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A10 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR COLOR PRESET · sRGB: Set the screen color to fit the SRGB standard color specification. [. . . ] If necessary, perform the white balance function again. This function will be enabled only when the input signal is an analog signal. A12 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the right side of the monitor. Menu Name Icons Sub-menu Name button on the FLATRON F-ENGINE When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side. Touch the SET button to use the adjusted screen. Screen when applied Screen when not applied Main menu Sub menu Description MOVIE This feature lets you easily select the best desired TEXT image condition optimized to the environment (ambient illumination, image types etc). MOVIE: For animation images in videos or movies TEXT: For text images (Word processing etc. ) USER User You can manually adjust brightness, ACE or RCM. [. . . ]