User manual LG L1917S-BN

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Adjust the stand base's angle by holding the edges of the monitor gently with both hands. Important This illustration depicts the typical connection procedure. Your monitor may differ from the one displayed in the pictures above. Do not touch or apply force to the monitor's screen while expanding or folding the stand base. A3 Connecting the Display Folding the stand base 1. Face the front of the monitor dislpay. Than gently push the monitor backwards, following the sequence shown in the picture below. Tilt range 1. Make sure that the angle of the panel is set for your comfort. Tilt Range : 0°~30 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees A4 Connecting the Display To adjust the height Scope of adjusting the height : maximum 4. 76 inches (121 mm) 121 mm A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and form 1 to 2 . A Connect DVI Cable B Connect Dsub Cable (PC) C Connect Dsub Cable (Mac) NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. product. Connect the cable as below sketch map Power Cord 2 1 Signal Cable Varies according to model. Wall-outlet type PC-outlet type DVI-D(This feature is not available in all countries. ) PC PC MAC Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 2. Press button on the side switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make by using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making any image adjustments. To make adjustments in the On Screen Display, follow these steps: MENU -+ AUTO/SET -+ MENU Press the MENU button, then the main menu of the OSD appears. To select each item in the OSD menu, use the - or + button. When the icon you want is highlighted, press the AUTO/SET Button. Use the - / + buttons to adjust the image to the desired level. Use the AUTO/SET button to select other sub-menu items. Press the MENU button once to return to the main menu to select another function. Press the MENU button twice to exit from the OSD. A10 On Screen Display (OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu PICTURE Sub-menu BRIGHTNESS CONTRAST GAMMA COLOR PRESET RED GREEN BLUE HORIZONTAL POSITION VERTICAL CLOCK SHARPNESS SETUP LANGUAGE OSD HORIZONTAL A D Reference To adjust the brightness, contrast and gamma of the screen To customize the color of the screen sRGB 6500K 9300K To adjust the position of the screen To improve the clarity and stability of the screen TRACKING PHASE POSITION VERTICAL To customize the screen status for a user's operating environment WHITE BALANCE POWER INDICATOR 4:3 IN WIDE FLATRON F-ENGINE FACTORY RESET MOVIE / TEXT USER NORMAL To select or customize desired image settings : Adjustable A : Analog Input D : Digital Input NOTE The order of icons may differ depending on the model (A11~A16). A11 On Screen Display (OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name PICTURE Icons Sub-menus Button Tip MENU -+ SET : Exit : Adjust (Decrease/Increase) : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A12 On Screen Display (OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. [. . . ] · Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. G On the screen background, vertical bars or stripes are visible. · Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. · Press the AUTO/SET button to automatically adjust your display image to the ideal setting. [. . . ]