User manual LG L192WS-SN

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] The product may fall and get damaged or injure your foot. A4 REAR Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° 20 Warning: When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. When attached, tighten the thumbscrews to secure the 3. Connect the power cord into a proper power outlet that is easily accessible and close to the display. 1 19 inch monitor Signal Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. Power Cord Analog signal Digital signal D-sub DVI Varies according to model. Wall-outlet type 2 1 PC-outlet type PC MAC Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. PC DVI-D(This feature is not available in all countries. ) A6 Connecting the Display 20. 1 inch monitor Signal Cable Analog signal Digital signal Power Cord D-sub DVI Varies according to model. Wall-outlet type NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. 2 1 PC-outlet type PC DVI-D(This feature is not available in all countries. ) PC MAC Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 4. Press button on the front switch panel to turn the power on. If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. A10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A11 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu PICTURE Sub-menu BRIGHTNESS CONTRAST GAMMA COLOR PRESET RED GREEN BLUE HORIZONTAL POSITION VERTICAL CLOCK SHAPNESS SETUP LANGUAGE OSD HORIZONTAL A D Reference To adjust the brightness, contrast and gamma of the screen To customize the color of the screen sRGB 6500K 9300K To adjust the position of the screen To improve the clarity and stability of the screen TRACKING PHASE POSITION VERTICAL To customize the screen status for a user's operating environment WHITE BALANCE POWER INDICATOR FACTORY RESET FLATRON F-ENGINE MOVIE / TEXT USER NORMAL To select or customize desired image settings : Adjustable A : Analog Input D : Digital Input NOTE The order of icons may differ depending on the model (A12~A16 ). A12 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. [. . . ] If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. · Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color). G Any horizontal noise appearing in any image or characters are not clearly portrayed. Important Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. [. . . ]