User manual LG L1930SQ

[. . . ] If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. [. . . ] Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 2. Place the monitor face Down on the cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. . If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 6 Connecting the Display 4. Pushing the PUSH button, Take the stand body from hinge body. Good Position Bad Position Warning: You can hurt your finger. 7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 8 Connecting the Display Connecting with the PC W1946T/W1946TN/W2046T/W2246T/W2346T 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. When only one signal is connected, it is automatically detected. (Only W1946T/W1946TN/W2046T/W2246T/W2346T ) EXIT Button Exit the OSD(On Screen Display). Power Button & Use this button to turn the display on or off. Power Indicator The power indicator stays white if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking white. 13 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. To access a control, use the corresponding Buttons. Use the Use the / Buttons to adjust the image to the desired level. : 0 / 1 / 2 On the monitor, high gamma values display whitish images and low gamma values display blackish images. Exit : Exit USER : Decrease : Increase : Select another sub-menu : Restart to select sub-menu 17 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description W1946T/W1946TN/W2046T/W2246T/W2346T HORIZONTAL To move image left and right. VERTICAL CLOCK To move image up and down. To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. [. . . ] packing) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 0. 8 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type NOTE Information in this document is subject to change without notice. 27 Specifications Display 50. 8 cm (20. 0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50. 8 cm 0. 2766 x 0. 2766 mm (Pixel pitch) Horizontal Freq. Input Form 30 kHz to 83 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate Sync. SOG (Sync On Green), Digital W2046T Sync Input Video Input Signal Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital VESA 1600 x 900 @ 60 Hz VESA 1600 x 900 @ 60 Hz Resolution Plug&Play Power Consumption Dimensions & Weight Max Recommend DDC 2B(Digital), DDC2AB(Anlaog) On Mode Sleep Mode Off Mode : 24 W(Typ. ) 0. 5 W 0. 5 W Without Stand Width 47. 58 cm (18. 73 inch) Height 30. 35 cm ( 11. 94 inch) Depth 6. 08 cm ( 2. 39 inch) 3. 2 kg (7. 11 lb) With Stand Width 47. 58 cm (18. 73 inch) Height 37. 64 cm (14. 81 inch) Depth 16. 99 cm ( 6. 68 inch) Weight(excl. packing) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 1. 0 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type NOTE Information in this document is subject to change without notice. 28 Specifications Display 50. 8 cm (20. 0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50. 8 cm 0. 2766 x 0. 2766 mm (Pixel pitch) Horizontal Freq. [. . . ]