User manual LG L1932S

[. . . ] Note · · · Remove the Styrofoam and vinyl cover. After unpacking the package, make sure to check the contents of the package. Make sure to keep the package box for transporting the product in the future. After unpacking, you may use the lower part of the package box as a temporary stand for product test or operation check. Introduction Unpacking LCD Display Manuals Warranty Card Quick Setup Guide (Not available in all locations) User's Guide MagicInfo Software CD MagicInfo Manual CD (Applicable to the FPn-2 model only) Cables Power Cord Others Batteries (AAA X 2) Remote Control (Not available in all locations) HDD Cover (Applicable to the FPn-2 model only) Introduction Ferrite Core for Lan Cable BNC to RCA Adaptor Jack (Applicable to the 46-inch network model only. ) Sold separately D-Sub Cable DVI Cable Wall Mount KIT LAN Cable (Applicable to the FPn-2 model only) TV tuner box NetWork Box (Applicable to the FP-2 model only) Semi Stand KIT BNC Cable Note You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals. [. . . ] 2. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. Note You can adjust the bracket angle between -2° and 15°. Introduction Make sure to use the top center, and not the leftor the right side of the product to adjust the angle. Mechanical Layout(L1932S, 460FPn-2) Mechanical Layout Introduction LCD Display Head NETWORK MODEL SIZE Installation VESA Bracket · · When installing VESA, make sure to comply with the international VESA standards. Purchasing VESA Bracket and Installation Information : Please contact your nearest LG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. At least 2 persons are needed in order to move the LCD Display. LG is not responsible for any product damage or any injury caused by installation at customer's discretion. · · Introduction Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation · · · Contact a technician for installing the wall bracket. Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. ABC- LCD Display Wall Bracket Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. 2. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. Then, start the Camcorders with a tape inserted. 4. The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store. ) If your camcorder is stereo, you need to connect a set of two cables. Connecting a DVD Player Connections 1. Connect a set of audio cables between the AV AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the DVD player. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the DVD player. Note · · Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. Then, start the DVD Player with a DVD disc inserted. Note · A component cable is optional. For an explanation of Component video, consult your DVD manual. Connecting a DTV Set Top Box Note · The connections for a typical Set Top Box are shown below. 1. 2. Connect a Component cable between the BNC / COMPONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the AV AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. [. . . ] 3) Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen. Then, enable the USB Boot First option by selecting that option and pressing the Enter key in the Boot menu. 4) Switch your set on while your USB disk is connected and boot up in DOS mode. 5) Run C:\ghost. exe and choose Local !' Partition !' From Image from the menu. [. . . ]