User manual LG L1940PQ

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° Swivel Range : 350° Height Range : maximum 3. 94 inches (100. 0mm) 100. 0mm * Please be sure to remove the Locking pin to adjust the height. Ergonomic You do not need to replace the Locking pin after it is removed, to adjust its height. It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect signal input cable 1 and power cord 2 in order, then tighten the screw of the signal cable. A Connect D-sub Cable (PC) B Connect D-sub Cable (Mac) C Connect DVI-D Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product. Power Cord 2 1 Signal Cable Varies according to model. Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. Wall-outlet type PC MAC PC DVI-D(This feature is not available in all countries. ) 2. Touch the power button on the front of panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power button NOTE 'Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. This feature is used when two computers are connected to the display. The default setting is D-Sub. AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always touch the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 1920 x 1200 Power Button Use this button to turn the display on or off. Power Indicator This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. A10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: Touch the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, touch the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. [. . . ] · You can secure the current control settings, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message "OSD UNLOCKED" will appear. A18 Troubleshooting Display image is incorrect G Display Position is incorrect. · Touch the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. G On the screen background, vertical bars or stripes are visible. · Touch the AUTO/SET button to automatically adjust your display image to the ideal setting. [. . . ]