User manual LG L1942H-BF

[. . . ] User's Guide L1942H Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] Your monitor may differ from the one displayed in the pictures above. Do not touch or apply force to the monitor's screen while expanding or folding the stand base. A3 Connecting the Display Folding the stand base 1. Then gently push the monitor backwards, following the sequence shown in the picture below. Tilt range 1. Make sure that the angle of the panel is set for your comfort. Tilt Range : 0°~30° Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees A4 Connecting the Display To adjust the height Scope of adjusting the height: maximum 4. 16 inches (105. 7 mm) 105. 7 mm A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect DVI Cable B Connect Dsub Cable (PC) C Connect Dsub Cable (Mac) NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product. Power Cord Signal Cable Varies according to model. Wall-outlet type DVI-D (This feature is not available in all countries. ) Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 2. Press button on the side switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) NOTE 'Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. A6 Connecting the Display To arrange the cables 1. Insert and screw the cable holder into the hole in the back of the stand until it will not turn any more as shown in the following figure. 2. After connecting the cables neatly, arrange the cables to the Cable Holder as shown in the following figure. Cable Holder A7 Control Panel Functions Front Panel Controls MENU AUTO/SET ENGINE SOURCE Control Function Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" appears. MENU Button A8 Control Panel Functions Control Buttons Button ( ) Function Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A16. Button (SOURCE) Use this button to make either D-Sub or DVI connector active. This feature is used when two computers are connected to the display. [. . . ] You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message "OSD UNLOCKED" will appear. A17 Troubleshooting Display image is incorrect Display Position is incorrect. · Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. On the screen background, vertical bars or stripes are visible. · Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. [. . . ]