User manual LG L1950B-SF

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Turn the screw to the left to separate the stand body from the stand base. IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~15° -5 15 IMPORTANT It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). 4 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. When attached, tighten the thumbscrews to secure the connection. Connect the power cable 2 with the AC-DC adapter (AC-DC power supply) 3 , and then plug the cable in the outlet. 2. Connect the signal cable NOTE This is a simplified representation of the rear view. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: -+ + -+ Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Press the MENU Button once to return to the main menu to select another function. Press the MENU Button twice to exit from the OSD. -+ 9 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu EZ ZOOMING 4:3 IN WIDE NORMAL Sub-menu A D Reference To adjust the resolution To adjust the image size PHOTO EFFECT GAUSSIAN BLUR SEPIA MONOCHROME BRIGHTNESS To adjust the screen color mode PICTURE CONTRAST GAMMA sRGB PRESET 6500K 9300K To adjust the brightness, contrast and gamma of the screen COLOR RED GREEN BLUE HORIZONTAL VERTICAL To customize the color of the screen To adjust the position of the screen To improve the clarity and stability of the screen TRACKING CLOCK PHASE SHARPNESS LANGUAGE HORIZONTAL OSD POSITION VERTICAL SETUP WHITE BALANCE RTC POWER INDICATOR FACTORY RESET MOVIE INTERNET USER NORMAL DEMO To customize the screen status for a user's operating environment FLATRON F-ENGINE To select or customize desired image settings : Adjustable A : Analog Input D : Digital Input NOTE The order of icons may differ depending on the model (10~16). OSD (On Screen Display) menu languages on the monitor may differ from the manual. 10 On Screen Display(OSD) Selection and Adjustment Pressing the button on the right side of the monitor will display the OSD screen. MENU : Exit - , + : Move SET : Select Main menu EZ ZOOMING Description To select the display resolution. When you select 'EZ ZOOMING' in OSD, display resolution goes one step down so characters and images look bigger. [. . . ] See the 'Specifications' section of this manual and configure your display again. · This message appears when the signal cable between your PC and your display is not connected. Check the signal cable and try again. G Do you see an "OUT OF RANGE" message on the screen? G Do you see a "CHECK SIGNAL CABLE" message on the screen? Do you see a "OSD LOCKED" message on the screen? G Do you see "OSD LOCKED" when you push MENU button?· You can secure the current control settings, so that they cannot be inadvertently changed. [. . . ]